HP LH4r HP Netserver LH 6000 Installation Guide - Page 82

Install the corresponding VRM by aligning the VRM with the slot. Note

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Chapter 7 Installing Additional Processors Figure 7-3. Open the Latches 12. Align the processor being added over the next available slot so that the heat sink faces away from the system board for processors 1, 2, and 3, and towards the system board for processors 4, 5, and 6. 13. Gently push down on the processor being added until it is fully seated. 14. Rotate the retaining latches to seat the processor firmly in the connector. 15. Close the access covers to the processor slots and tighten the thumbscrew (see Figure 7-2). 16. Install the corresponding VRM by aligning the VRM with the slot. Note that the component side of the VRM will face toward the system board. CAUTION Push down on the printed circuit of the VRM -- do not push down on the VRM components. 17. Gently insert the VRM into the slot (see Figure 7-4). 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter
7
Installing Additional Processors
74
Figure 7-3. Open the Latches
12.
Align the processor being added over the next available slot so that the
heat sink faces away from the system board for processors 1, 2, and 3, and
towards the system board for processors 4, 5, and 6.
13.
Gently push down on the processor being added until it is fully seated.
14.
Rotate the retaining latches to seat the processor firmly in the connector.
15.
Close the access covers to the processor slots and tighten the thumbscrew
(see Figure 7-2).
16.
Install the corresponding VRM by aligning the VRM with the slot. Note
that the component side of the VRM will face toward the system board.
CAUTION
Push down on the printed circuit of the VRM -- do not push
down on the VRM components.
17.
Gently insert the VRM into the slot (see Figure 7-4).