HP LH4r HP Netserver LH 6000 Installation Guide - Page 73

board into the slot.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 6 Installing Additional Boards NOTE To prevent intermittent problems, ensure each unused PCI slot has a PCI slot cover. If a PCI board is removed and not re-installed, you must install a PCI slot cover. CAUTION Do not bend the PCI board to install it into the slot. If the PCI board is full-length, the PCI front board hold-down at the rear of the PCI slot is used to hold the board in place. The front board hold down prevents the board from moving during NetServer transportation and handling. 11. Before installing the PCI board: ◊ Verify there is no handle attached to it, especially if it is a full-length board. ◊ If it has a handle attached, remove the handle before installing the board into the slot. 12. Align the board with its slot, along its full length, and position it into the slot (see Figure 6-5). NOTE Slots are keyed to prevent a board from going into the wrong slot. 13. Push the PCI board down into its connector in the I/O board. 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 6
Installing Additional Boards
65
NOTE
To prevent intermittent problems, ensure each unused PCI slot
has a PCI slot cover. If a PCI board is removed and not
re-installed, you must install a PCI slot cover.
CAUTION
Do not bend the PCI board to install it into the slot.
If the PCI board is full-length, the PCI front board hold-down
at the rear of the PCI slot is used to hold the board in place.
The front board hold down prevents the board from moving
during NetServer transportation and handling.
11.
Before installing the PCI board:
◊
Verify there is no handle attached to it, especially if it is a full-length
board.
◊
If it has a handle attached, remove the handle before installing the
board into the slot.
12.
Align the board with its slot, along its full length, and position it into the
slot (see Figure 6-5).
NOTE
Slots are keyed to prevent a board from going into the wrong
slot.
13.
Push the PCI board down into its connector in the I/O board.