HP LH4r HP Netserver LH 6000 Installation Guide - Page 41

Replacing the LH 6000r Rack Mount Covers

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Chapter 3 Opening and Closing the HP NetServer 6. Remove the top cover by loosening the thumbscrew and pulling the cover forward to disengage it. Lift it up and away from the chassis (see Figure 3-6). Top Cover Thumbscrew Right Cover Thumbscrew Thumbscrew Bottom Cover Figure 3-6. HP NetServer LH 6000r Covers 7. Remove the right cover by supporting it with your hand, then loosening the thumbscrew and pulling the cover forward, then down to disengage it. Lift it away from the chassis (see Figure 3-6). 8. Remove the bottom cover by supporting it with your hand, and loosening the thumbscrew with the other hand. Pull the cover forward to disengage it and catch it as it falls away from the chassis (see Figure 3-6). Replacing the LH 6000r Rack Mount Covers 1. For each of the side covers, insert the two metal tabs, at the end opposite the handle, into the two openings at the top and bottom corners of the chassis. Hold the cover in place, but do not slide the tabs in completely. 2. Align the four, widely spaced, metal tabs on the cover's long, top edge against the leftmost edge of the four widely spaced openings on the top of the chassis. 3. Hold the top of the cover in this position with one hand, while pressing the bottom edge of the cover with the other hand until the cover is completely flush against the chassis. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 3
Opening and Closing the HP NetServer
33
6.
Remove the top cover by loosening the thumbscrew and pulling the cover
forward to disengage it. Lift it up and away from the chassis (see Figure
3-6).
Top Cover
Right Cover
Bottom Cover
Thumbscrew
Thumbscrew
Thumbscrew
Figure 3-6. HP NetServer LH 6000r Covers
7.
Remove the right cover by supporting it with your hand, then loosening the
thumbscrew and pulling the cover forward, then down to disengage it. Lift
it away from the chassis (see Figure 3-6).
8.
Remove the bottom cover by supporting it with your hand, and loosening
the thumbscrew with the other hand. Pull the cover forward to disengage it
and catch it as it falls away from the chassis (see Figure 3-6).
Replacing the LH 6000r Rack Mount Covers
1.
For each of the side covers, insert the two metal tabs, at the end opposite
the handle, into the two openings at the top and bottom corners of the
chassis. Hold the cover in place, but do not slide the tabs in completely.
2.
Align the four, widely spaced, metal tabs on the cover’s long, top edge
against the leftmost edge of the four widely spaced openings on the top of
the chassis.
3.
Hold the top of the cover in this position with one hand, while pressing the
bottom edge of the cover with the other hand until the cover is completely
flush against the chassis.