HP LH4r HP Netserver LH 6000 Installation Guide - Page 74

Refer to the accessory board documentation for connection requirements.

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Chapter 6 Installing Additional Boards Figure 6-5. Installing an Accessory Board 14. Lower the retainer. 15. Secure the PCI board by rotating the locking lever counter-clockwise to hold the retainer (see Figure 6-3). NOTE Be sure the PCI latch and retainer close fully so that the slot will power on when the NetServer reboots. 16. Replace the PCI front board hold down. 17. If the installed accessory board requires an external connection, or a connection to the I/O board, ensure the cable is properly attached. Refer to the accessory board documentation for connection requirements. 18. Follow the procedure in Chapter 3, "Opening and Closing the HP NetServer," for closing up the server. 19. Reconnect power and cables. 20. Power on the HP NetServer according to the respective NOS power up instructions. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 6
Installing Additional Boards
66
Figure 6-5. Installing an Accessory Board
14.
Lower the retainer.
15.
Secure the PCI board by rotating the locking lever counter-clockwise to
hold the retainer (see Figure 6-3).
NOTE
Be sure the PCI latch and retainer close fully so that the slot
will power on when the NetServer reboots.
16.
Replace the PCI front board hold down.
17.
If the installed accessory board requires an external connection, or a
connection to the I/O board, ensure the cable is properly attached.
Refer to the accessory board documentation for connection requirements.
18.
Follow the procedure in Chapter 3, "Opening and Closing the HP
NetServer," for closing up the server.
19.
Reconnect power and cables.
20.
Power on the HP NetServer according to the respective NOS power up
instructions.