HP LH4r HP Netserver LH 6000 Installation Guide - Page 16

Con Remote Management: If you plan to manage the HP NetServer

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 1 Setting Up the HP NetServer LH 6000/6000r ◊ Select "Yes" to choose automated NOS installation for first-time installation of Novell NetWare or Microsoft Windows NT Server on a factory-configured HP NetServer. ◊ Select No to use the manual NOS installation if: ∗ You are installing a NOS other than Novell NetWare or Microsoft Windows NT Server. ∗ You have replaced accessory components. ∗ You have replaced HP accessories with non-HP accessories. 11. View Configuration Advisories: Read the Configuration Advisories and print them if necessary. Make any changes suggested in the advisories. 12. Configure Remote Management: If you plan to manage the HP NetServer LH 6000 remotely, refer to the HP NetServer Server Management Reference Guide for instructions. Select "Configure Remote Management" on the Navigator screen to configure Integrated Remote Assistant. 13. Show System Information: Select "View System Information" to get information about accessory boards and devices. Select "View Resources" to view used and available system resources. 14. Install the NOS: If you selected the HP automated NOS installation process, you will be guided through the process by a series of HP display screens: ◊ Install Utility Partition: This step creates a disk utility partition on the server boot hard disk drive where HP Navigator will copy troubleshooting and other utilities. NOTE Select "Execute" on the Install Utility Partition screen to install the partition. The utility partition is not available under SCO UnixWare. ◊ Execute Card Utilities: Select "Execute" on the Execute Card Utilities screen to run the accessory board configuration utilities. ◊ Follow the instructions on the screen and in the network operating system's installation instructions to perform the manual NOS installation. ◊ For Manual NOS Installation Only: Before you perform a manual NOS installation, print out instructions and create NOS-specific driver diskette(s), as follows: 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 1
Setting Up the HP NetServer LH 6000/6000r
8
◊
Select "Yes" to choose automated NOS installation for first-time
installation of Novell NetWare or Microsoft Windows NT Server on a
factory-configured HP NetServer.
◊
Select No to use the manual NOS installation if:
You are installing a NOS other than Novell NetWare or Microsoft
Windows NT Server.
You have replaced accessory components.
You have replaced HP accessories with non-HP accessories.
11.
View Configuration Advisories: Read the Configuration Advisories and
print them if necessary. Make any changes suggested in the advisories.
12.
Configure Remote Management: If you plan to manage the HP NetServer
LH 6000 remotely, refer to the
HP NetServer Server Management
Reference Guide
for instructions. Select "Configure Remote Management"
on the Navigator screen to configure Integrated Remote Assistant.
13.
Show System Information: Select "View System Information" to get
information about accessory boards and devices. Select "View Resources"
to view used and available system resources.
14.
Install the NOS: If you selected the HP automated NOS installation
process, you will be guided through the process by a series of HP display
screens:
◊
Install Utility Partition: This step creates a disk utility partition on the
server boot hard disk drive where HP Navigator will copy
troubleshooting and other utilities.
NOTE
Select "Execute" on the Install Utility Partition screen to install
the partition. The utility partition is not available under SCO
UnixWare.
◊
Execute Card Utilities: Select "Execute" on the Execute Card Utilities
screen to run the accessory board configuration utilities.
◊
Follow the instructions on the screen and in the network operating
system’s installation instructions to perform the manual NOS
installation.
◊
For Manual NOS Installation Only: Before you perform a manual NOS
installation, print out instructions and create NOS-specific driver
diskette(s), as follows: