HP LH4r HP Netserver LH 6000 Installation Guide - Page 21

Door reveals this panel

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Chapter 2 Lock Status Screen Controls, Ports, and Indicators Door reveals this panel Power Switch Power-on LED Reset Switch Secure Mode Switch Reset Secure Mode LED Server Status LEDs Escape Enter Scroll Scroll Down Up Figure 2-3. Front Panel Console Table 2-1. Front Panel Console Switch and Indicator Definitions Control Description Lock (LH 6000 only) Locked Locks system to prevent unauthorized use. Note that locking and unlocking of the enclosure is reported to the system event log (SEL). Open DC Power Switch and LED Turns the NetServer on and off. This switch is under the protective door on the front panel. Push once to turn on, again to turn off. As long as the AC power is connected to the NetServer, standby power is present. l If the LED is steady green, then the NetServer is powered-up. l If the LED is flashing green, the NetServer is in a power-save mode. l If the LED is off, but the two-line display has a message, standby power is present. If the NetServer is set up to go into power-save mode, the power switch is depressed; you must press it for more than four seconds to effect a power down. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 2
Controls, Ports, and Indicators
13
Power
Switch
Reset
Switch
Power-on
LED
Escape
Scroll
Down
Scroll
Up
Status
Screen
Server
Status
LEDs
Secure
Mode
LED
Secure
Mode
Switch
Door reveals this panel
Lock
Enter
Reset
Figure 2-3. Front Panel Console
Table 2-1. Front Panel Console Switch and Indicator Definitions
Control
Description
Lock (LH 6000 only)
Locked
Open
Locks system to prevent unauthorized use.
Note that locking and unlocking of the enclosure is reported to
the system event log (SEL).
DC Power Switch
and LED
Turns the NetServer on and off. This switch is under the
protective door on the front panel. Push once to turn on, again
to turn off. As long as the AC power is connected to the
NetServer, standby power is present.
If the LED is steady green, then the NetServer is
powered-up.
If the LED is flashing green, the NetServer is in
a power-save mode.
If the LED is off, but the two-line display has a
message, standby power is present.
If the NetServer is set up to go into power-save mode, the
power switch is depressed; you must press it for more than four
seconds to effect a power down.