HP LH4r HP Netserver LH 6000 Installation Guide - Page 76

Removing a Hot Plug Board

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Chapter 6 Installing Additional Boards To access the PCI Hot Plug Replacement procedures for the respective NOS, you must have the HP NetServer Navigator CD-ROM provided with the HP NetServer LH 6000. To view the respective Hot Plug Replacement (NOS) procedures: 1. Insert the HP NetServer Navigator CD-ROM into a CD drive. 2. Select NetServers LH-Series button. 3. Scroll down to and select NetServer LH 6000 in the list. 4. Select Install. 5. Select Installing Accessory Boards. 6. Select the appropriate Hot Plug Replacement topic. NOTE To perform a hot add, or a hot replacement when the HP NetServer is powered up, refer to the PCI Hot Plug Help file on the HP NetServer Navigator CD-ROM. Removing a Hot Plug Board To remove a hot-plug board from the HP NetServer which has not been powered up: 1. Make sure power is off and follow the instructions for accessing the I/O board. 2. Open the PCI hold-down latch. 3. Pull the gray plastic slot ejector (see Figure 6-6) out until you feel resistance (about three-eighths of an inch, or 10mm). This releases the hot-plug board from the I/O board connector. 68

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 6
Installing Additional Boards
68
To access the PCI Hot Plug Replacement procedures for the respective NOS, you
must have the
HP NetServer Navigator CD-ROM
provided with the HP NetServer
LH 6000.
To view the respective Hot Plug Replacement (NOS) procedures:
1.
Insert the
HP NetServer Navigator CD-ROM
into a CD drive.
2. Select
NetServers LH-Series
button.
3.
Scroll down to and select
NetServer LH 6000
in the list.
4. Select
Install
.
5. Select
Installing Accessory Boards
.
6.
Select the appropriate
Hot Plug Replacement
topic.
NOTE
To perform a
hot add
, or a
hot replacement
when the HP
NetServer is powered up, refer to the PCI Hot Plug Help file on
the
HP NetServer Navigator CD-ROM
.
Removing a Hot Plug Board
To remove a hot-plug board from the HP NetServer which has not been powered
up:
1.
Make sure power is off and follow the instructions for accessing the I/O
board.
2.
Open the PCI hold-down latch.
3.
Pull the gray plastic slot ejector (see Figure 6-6) out until you feel
resistance (about three-eighths of an inch, or 10mm).
This releases the hot-plug board from the I/O board connector.