HP LH4r HP Netserver LH 6000 Installation Guide - Page 70

Installing Accessory Boards

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Chapter 6 Installing Additional Boards Installing Accessory Boards NOTE To perform a hot add, or a hot replacement when the HP NetServer is powered up, refer to help information provided on the HP NetServer Navigator CD-ROM provided with your NetServer. Use this procedure to install all PCI accessory boards for the following situations: • The initial installation of PCI Hot Plug boards • All PCI boards without hot-plug compliant drivers installed or removed in slots 1 through 8. • Read the documentation included with each board and follow any special instructions provided. CAUTION For non-Hot Plug PCIs: To prevent a system crash or hang, never open the PCI latch and retainer of a PCI board with the NetServer powered on. Always turn power off to the NetServer before opening the PCI latch and retainer. For Hot Plug PCIs: Only a PCI Hot Plug utility allows you to turn power off to the slot, before opening the PCI latch and retainer with power applied to the NetServer. The installation procedure is the same for the rack-mount and the pedestal NetServers once you gain access to the I/O board. 1. Log off all users and gracefully shut down the network operating system according to directions in your NOS documentation. 2. Power down the NetServer according to the instructions in Chapter 2, "Controls, Ports, and Indicators." 3. Disconnect the power cords and cables and, if necessary, label each one to support re-assembly. CAUTION The power supplies will continue to provide standby current to the NetServer until the power cables are disconnected. 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 6
Installing Additional Boards
62
Installing Accessory Boards
NOTE
To perform a
hot add
, or a
hot replacement
when the HP
NetServer is powered up, refer to help information provided on
the
HP NetServer Navigator CD-ROM
provided with your
NetServer.
Use this procedure to install all PCI accessory boards for the following situations:
•
The initial installation of PCI Hot Plug boards
•
All PCI boards without hot-plug compliant drivers installed or removed in
slots 1 through 8.
•
Read the documentation included with each board and follow any special
instructions provided.
CAUTION
For non-Hot Plug PCIs:
To prevent a system crash or hang, never open the PCI latch
and retainer of a PCI board with the NetServer powered on.
Always turn power off to the NetServer before opening the
PCI latch and retainer.
For Hot Plug PCIs:
Only a PCI Hot Plug utility allows you to turn power off to the
slot, before opening the PCI latch and retainer with power
applied to the NetServer.
The installation procedure is the same for the rack-mount and the pedestal
NetServers once you gain access to the I/O board.
1.
Log off all users and gracefully shut down the network operating system
according to directions in your NOS documentation.
2.
Power down the NetServer according to the instructions in Chapter 2,
"Controls, Ports, and Indicators."
3.
Disconnect the power cords and cables and, if necessary, label each one to
support re-assembly.
CAUTION
The power supplies will continue to provide standby current to
the NetServer until the power cables are disconnected.