HP LH4r HP Netserver LH 6000 Installation Guide - Page 126

Security

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

Chapter 10 Configuring the HP NetServer ◊ I20 Settings - Use this menu to set the maximum number of I20 drives (4), the message timeout multiplier (1 to 1000), the pause interval during POST, or start the IRTOS (I20 Real Time Operating System) manually. ◊ Embedded LAN & SCSI Settings - Use this menu to: ∗ Change between HP NetRAID (default) and LVD SCSI modes. ∗ Set the Embedded NIC to enable, disable, or enable as a boot device (Boot ROM Enabled). If the embedded NIC is enabled as a boot device, boot ROMs for enabled SCSI devices cannot be loaded. ∗ Enable and disable the Wake-On-LAN feature. ◊ Keyboard & Mouse Settings - Use this menu to set the parameters of the keyboard, including NumLock, and set the PS/2 mouse to Auto (detect)/Enabled/Disabled. Disabling the mouse frees up IRQ 12, but prevents any installed PS/2 mouse from functioning. ◊ Flexible Disk & IDE Settings - Use this menu to enable/disable the local bus IDE drive. Use this menu to change the flexible disk type or add an IDE hard drive to HP NetServer's configuration. This would include selecting the hard drive's characteristics, manually or automatically, and selecting which drive would be the Primary Master or Slave, the CD-ROM or the IDE hard drive. ◊ Processor/Memory Settings - Use this menu to enable the processor module's serial number (if supported) being read by firmware, enable memory caching, and/or add an extended memory gap in system address space. • Security - Two submenus are provided. ◊ Power-On Password - Sets the administrator and user passwords and sets the system requirement for a password after booting. The Administrator password must be set before setting the User password. Once the administrator password is set, the administrator can access and change all fields in the screens. If the User password is set, the user may only change the system time, date, and user password. The user may view all fields, but can not alter any of the settings. ◊ Hardware Security - Sets the system parameters for operating in Secure Mode. 118

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 10
Configuring the HP NetServer
118
◊
I
2
0 Settings
– Use this menu to set the maximum number of I
2
0 drives
(4), the message timeout multiplier (1 to 1000), the pause interval
during POST, or start the IRTOS (I
2
0 Real Time Operating System)
manually.
◊
Embedded LAN & SCSI Settings – Use this menu to:
Change between HP NetRAID (default) and LVD SCSI modes.
Set the Embedded NIC to enable, disable, or enable as a boot
device (Boot ROM Enabled).
If the embedded NIC is enabled as a boot device, boot ROMs for
enabled SCSI devices cannot be loaded.
Enable and disable the Wake-On-LAN feature.
◊
Keyboard & Mouse Settings – Use this menu to set the parameters of
the keyboard, including NumLock, and set the PS/2 mouse to Auto
(detect)/Enabled/Disabled. Disabling the mouse frees up IRQ 12, but
prevents any installed PS/2 mouse from functioning.
◊
Flexible Disk & IDE Settings – Use this menu to enable/disable the
local bus IDE drive. Use this menu to change the flexible disk type or
add an IDE hard drive to HP NetServer's configuration. This would
include selecting the hard drive's characteristics, manually or
automatically, and selecting which drive would be the Primary Master
or Slave, the CD-ROM or the IDE hard drive.
◊
Processor/Memory Settings – Use this menu to enable the processor
module's serial number (if supported) being read by firmware, enable
memory caching, and/or add an extended memory gap in system
address space.
•
Security
– Two submenus are provided.
◊
Power-On Password – Sets the administrator and user passwords and
sets the system requirement for a password after booting.
The Administrator password must be set before setting the User
password. Once the administrator password is set, the administrator can
access and change all fields in the screens.
If the User password is set, the user may only change the system time,
date, and user password. The user may view all fields, but can not alter
any of the settings.
◊
Hardware Security – Sets the system parameters for operating in
Secure Mode.