HP LH4r HP Netserver LH 6000 Installation Guide - Page 89

Rack Assistant

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Chapter 8 Installing the HP NetServer in an HP Rack System/E or Rack System/U ◊ Install components from the bottom up. ◊ Place the heaviest components on the bottom of the rack. ◊ Use HP Rack Assistant to plan the rack configuration and to check power, weight, and stability of the configured rack. Download HP Rack Assistant from: http://netserver.hp.com/netserver/support/ Anti-tip Foot Leveler Feet Figure 8-2. Anti-Tip Foot and Leveler Feet l Install components such as DIMMs and processors into the system board assembly before rack-mounting the NetServer. l Remove power supplies and hard drives before lifting the HP NetServer. Always keep the following safety and environmental issues in mind, especially if you install the HP NetServer in a non-HP rack environment: • Maximum Recommended Ambient Temperature - The maximum recommended ambient temperature of the room is 35°C (95° F). • Elevated Operating Ambient Temperature - The ambient operating temperature within a closed or multi-unit rack assembly may exceed the room's ambient temperature. Ensure the temperature within the rack itself does not exceed 35°C (95° F). 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 8
Installing the HP NetServer in an HP Rack System/E or Rack System/U
81
◊
Install components from the bottom up.
◊
Place the heaviest components on the bottom of the rack.
◊
Use HP Rack Assistant to plan the rack configuration and to check
power, weight, and stability of the configured rack. Download HP
Rack Assistant from:
Leveler
Feet
Anti-tip
Foot
Figure 8-2. Anti-Tip Foot and Leveler Feet
Install components such as DIMMs and processors into the system board
assembly before rack-mounting the NetServer.
Remove power supplies and hard drives before lifting the HP NetServer.
Always keep the following safety and environmental issues in mind, especially if
you install the HP NetServer in a non-HP rack environment:
•
Maximum Recommended Ambient Temperature -
The maximum
recommended ambient temperature of the room is 35
°
C (95
°
F).
•
Elevated Operating Ambient Temperature -
The ambient operating
temperature within a closed or multi-unit rack assembly may exceed the
room’s ambient temperature. Ensure the temperature within the rack itself
does not exceed 35
°
C (95
°
F).