HP LH4r HP Netserver LH 6000 Installation Guide - Page 136

CTRL+C, Ctrl+C, Display=Verbose, Display=Terse, Enter, Verbose, Change Adapter, Status, Adapter Boot

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

Chapter 10 Configuring the HP NetServer NOTE If SCSI A and B on the I/O board are operating in RAID mode, the prompt to press CTRL+C is not displayed. To change to non-RAID mode, refer to "Start Setup Utility." If you wait too long to press the Ctrl+C keys, you may not be able to enter the Symbios Configuration utility, even though the message "Press Ctrl-C to start Symbios Configuration Utility..." is still displayed. If this happens, restart the HP NetServer, and press the Ctrl+C keys as soon as the message appears. 3. When the Symbios Logic SCSI Configuration Utility Main Menu is displayed, verify that shows Display=Verbose. (This means that the nonRAID SCSI devices will be listed on the boot screen.) If not, use the up and down arrow keys to highlight Display=Terse. Press Enter to change the setting to Verbose. 4. On the Symbios Logic SCSI Configuration Utility Main Menu, verify that the Current Status of all Symbios controllers (adapters) is On. If not, use the up and down arrow keys to highlight Change Adapter Status. Press Enter to display the Change Status on Next Boot window. Use the up and down arrow keys to highlight the controller, and press Enter to change its Next-Boot Status to On. Press Esc to return to the Main Menu. 5. On the Symbios Logic SCSI Configuration Utility Main Menu, use the up and down arrow keys to highlight Adapter Boot Order. Press Enter to select it. 128

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 10
Configuring the HP NetServer
128
NOTE
If SCSI A and B on the I/O board are operating in RAID mode,
the prompt to press
CTRL+C
is not displayed. To change to
non-RAID mode, refer to "Start Setup Utility."
If you wait too long to press the
Ctrl+C
keys, you may not be
able to enter the Symbios Configuration utility, even though
the message "Press Ctrl-C to start Symbios Configuration
Utility..." is still displayed. If this happens, restart the
HP NetServer, and press the
Ctrl+C
keys as soon as the
message appears.
3.
When the Symbios Logic SCSI Configuration Utility Main Menu is
displayed, verify that shows
Display=Verbose
. (This means that the non-
RAID SCSI devices will be listed on the boot screen.)
If not, use the up and down arrow keys to highlight
Display=Terse
. Press
Enter
to change the setting to
Verbose
.
4.
On the Symbios Logic SCSI Configuration Utility Main Menu, verify that
the Current Status of all Symbios controllers (adapters) is
On
.
If not, use the up and down arrow keys to highlight
Change Adapter
Status
. Press
Enter
to display the Change Status on Next Boot window.
Use the up and down arrow keys to highlight the controller, and press
Enter
to change its Next-Boot Status to
On
. Press
Esc
to return to the
Main Menu.
5.
On the Symbios Logic SCSI Configuration Utility Main Menu, use the up
and down arrow keys to highlight
Adapter Boot Order
. Press
Enter
to
select it.