HP LH4r HP Netserver LH 6000 Installation Guide - Page 88

Rack-mounting Guidelines and Precautions

Get HP LH4r - NetServer - 256 MB RAM PDF manuals and user guides View all HP LH4r manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Chapter 8 Installing the HP NetServer in an HP Rack System/E or Rack System/U NOTE The pedestal HP NetServer LH 6000 cannot be rack-installed without a conversion kit. Contact your HP reseller for information about the HP NetServer LH 6000 to LH 6000r Conversion Kit. Tools Required The following tools are required to mount the HP NetServer in the rack: • Torx 15 driver • Torx 25 driver • HP NetServer LH 6000r Rack Template l Tape or a marker pen to mark mounting locations Rack-mounting Guidelines and Precautions Observe the following guidelines and safety precautions during the rack-mount installation. l Extend the rack's anti-tip foot from under the front of the rack or insure that the anti-tip feature is installed (see Figure 8-2) prior to any work on the rack to prevent rack tip-over, equipment damage, and injury. WARNING Lower the leveler feet at the four corners of the rack to improve stability and prevent the rack from rolling away as devices are inserted into their rack mounts. Failure to use the anti-tip foot/device and leveler feet could result in serious injury. l Uneven mechanical loading within the rack can cause hazardous conditions. Plan the placement of equipment in the rack to ensure balanced loading. CAUTION If other rack components are to be mounted in the rack below the HP NetServer, install those components before starting to mount the NetServer. 80

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
Chapter 8
Installing the HP NetServer in an HP Rack System/E or Rack System/U
80
NOTE
The pedestal HP NetServer LH 6000 cannot be rack-installed
without a conversion kit. Contact your HP reseller for
information about the HP NetServer LH 6000 to LH 6000r
Conversion Kit.
Tools Required
The following tools are required to mount the HP NetServer in the rack:
•
Torx 15 driver
•
Torx 25 driver
•
HP NetServer LH 6000r Rack Template
Tape or a marker pen to mark mounting locations
Rack-mounting Guidelines and Precautions
Observe the following guidelines and safety precautions during the rack-mount
installation.
Extend the rack’s anti-tip foot from under the front of the rack or insure
that the anti-tip feature is installed (see Figure 8-2) prior to any work on
the rack to prevent rack tip-over, equipment damage, and injury.
WARNING
Lower the leveler feet at the four corners of the rack to
improve stability and prevent the rack from rolling away as
devices are inserted into their rack mounts. Failure to use the
anti-tip foot/device and leveler feet could result in serious
injury.
Uneven mechanical loading within the rack can cause hazardous
conditions. Plan the placement of equipment in the rack to ensure balanced
loading.
CAUTION
If other rack components are to be mounted in the rack below
the HP NetServer, install those components before starting to
mount the NetServer.