HP Workstation x4000 hp workstation x4000 - Technical Reference manual - Windo - Page 179

Installing a Processor,

Get HP Workstation x4000 PDF manuals and user guides View all HP Workstation x4000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 179 highlights

CAUTION Installing or Replacing Parts and Accessories Processor Installing a Processor To install a processor: 1. Turn off the display and shut down the Workstation. Disconnect all power cables and any LAN or telecommunications cables. 2. Remove the Workstation's cover (see page 145). 3. Place the Workstation on its side for better access. 4. Open the hard disk drive cage (see page 149). 5. Remove the Chassis Beam Assembly (see page 152). 6. Remove the MEC card (see page 162). 7. Ensure the processor is correctly oriented by matching the notches on the processor to the notches on the ZIF socket. Then carefully lower the new processor into place. When the processor is fully inserted, close the ZIF lever. Be extremely careful when you insert the processor. If you bend one of the pins, it will not go into the socket. Figure 10-22 Inserting a Processor Step 7 Step 9 8. Affix the new thermal interface material, provided with the new processor, to the top of the processor. 9. Attach the heatsink to the processor. Use the retaining clips to attach the heatsink. For easier installation, partially attach both clips by hooking one end of the side slot in each clip. Press down on the remaining ends of both clips until they click into place. Chapter 10 177

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
Installing or Replacing Parts and Accessories
Processor
Chapter 10
177
Installing a Processor
To install a processor:
1.
Turn off the display and shut down the Workstation. Disconnect all
power cables and any LAN or telecommunications cables.
2.
Remove the Workstation’s cover (see page 145).
3.
Place the Workstation on its side for better access.
4.
Open the hard disk drive cage (see page 149).
5.
Remove the Chassis Beam Assembly (see page 152).
6.
Remove the MEC card (see page 162).
7.
Ensure the processor is correctly oriented by matching the notches on
the processor to the notches on the ZIF socket. Then carefully lower
the new processor into place. When the processor is fully inserted,
close the ZIF lever.
CAUTION
Be extremely careful when you insert the processor. If you bend one of
the pins, it will not go into the socket.
Figure 10-22
Inserting a Processor
8.
Affix the new thermal interface material, provided with the new
processor, to the top of the processor.
9.
Attach the heatsink to the processor. Use the retaining clips to attach
the heatsink. For easier installation, partially attach both clips by
hooking one end of the side slot in each clip. Press down on the
remaining ends of both clips until they click into place.
Step 7
Step 9