IBM 7979B1U User Manual - Page 60

peripheral

Get IBM 7979B1U PDF manuals and user guides View all IBM 7979B1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Connector Retainer bracket Remote Supervisor Adapter II SlimLine Latch bracket To install a Remote Supervisor Adapter II SlimLine, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 28. 2. Turn off the server and peripheral devices and disconnect all power cords and external cables (see "Turning off the server" on page 13). Attention: In a dc power environment, only trained service personnel other than IBM service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply. 3. Remove the cover (see "Removing the cover" on page 31). 4. Remove the PCI riser-card assembly (see "Removing the riser-card assembly" on page 32). 5. Turn the Remote Supervisor Adapter II SlimLine so that the keys on the connector align correctly with the connector on the system board. 6. Slip the free end of the Remote Supervisor Adapter II SlimLine under the tab on the retainer bracket, aligning the holes in the adapter with the posts on the retainer bracket and latch bracket; then, press the adapter into the connector on the system board and make sure that all tabs on the latch bracket secure the adapter in place. 7. Replace the PCI riser-card assembly. See the documentation that comes with the Remote Supervisor Adapter II SlimLine for information about installing the firmware and configuring the adapter. Create a backup copy of the configuration so that if you have to replace the adapter in the future, you can restore the configuration. If you have other optional devices to install or remove, do so now. Otherwise, go to "Completing the installation" on page 81. 44 System x3650 Type 7979: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Remote Supervisor
Adapter II SlimLine
Connector
Latch bracket
Retainer bracket
To
install
a
Remote
Supervisor
Adapter
II
SlimLine,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
28.
2.
Turn
off
the
server
and
peripheral
devices
and
disconnect
all
power
cords
and
external
cables
(see
“Turning
off
the
server”
on
page
13).
Attention:
In
a
dc
power
environment,
only
trained
service
personnel
other
than
IBM
service
technicians
are
authorized
to
connect
or
disconnect
power
to
the
dc
power
supply.
See
the
documentation
that
comes
with
each
dc
power
supply.
3.
Remove
the
cover
(see
“Removing
the
cover”
on
page
31).
4.
Remove
the
PCI
riser-card
assembly
(see
“Removing
the
riser-card
assembly”
on
page
32).
5.
Turn
the
Remote
Supervisor
Adapter
II
SlimLine
so
that
the
keys
on
the
connector
align
correctly
with
the
connector
on
the
system
board.
6.
Slip
the
free
end
of
the
Remote
Supervisor
Adapter
II
SlimLine
under
the
tab
on
the
retainer
bracket,
aligning
the
holes
in
the
adapter
with
the
posts
on
the
retainer
bracket
and
latch
bracket;
then,
press
the
adapter
into
the
connector
on
the
system
board
and
make
sure
that
all
tabs
on
the
latch
bracket
secure
the
adapter
in
place.
7.
Replace
the
PCI
riser-card
assembly.
See
the
documentation
that
comes
with
the
Remote
Supervisor
Adapter
II
SlimLine
for
information
about
installing
the
firmware
and
configuring
the
adapter.
Create
a
backup
copy
of
the
configuration
so
that
if
you
have
to
replace
the
adapter
in
the
future,
you
can
restore
the
configuration.
If
you
have
other
optional
devices
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
81.
44
System
x3650
Type
7979:
User’s
Guide