IBM 7979B1U User Manual - Page 69

Installing, drive, 5-inch, model, server

Get IBM 7979B1U PDF manuals and user guides View all IBM 7979B1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Installing a SATA tape drive in a 2.5-inch model server To install a tape drive in a 2.5-inch model server, complete the following steps: 1. Read the safety information that begins on page vii and "Installation guidelines" on page 28. 2. Turn off the server and peripheral devices, and disconnect the power cords and all external cables. Attention: In a dc power environment, only trained service personnel other than IBM service technicians are authorized to connect or disconnect power to the dc power supply. See the documentation that comes with each dc power supply. 3. If you installed the space filler from the tape enablement kit onto the tape-drive assembly, remove it now. 4. Remove the server cover. 5. Remove the fan-bracket assembly. 6. Remove the filler panel from the tape-drive bay. 7. From the inside of the server, thread the tape-drive end of the cables for your tape drive through the rear of the tape-drive bay and out the front of the server. 8. Connect the cable or cables to the back of the tape drive. 9. Push the tape-drive assembly into the tape-drive bay, gently pulling the cables farther into the server as you do so, until the tape-drive assembly stops. 10. Push the tray handle to the closed (locked) position. 11. Connect the cable connectors to the following system-board connectors (see "System-board internal cable connectors" on page 19 for the location of the connectors): v Signal connector: SATA tape drive signal connector, J102 v Power connector: tape-drive power connector, J100 The following illustration shows the routing of the SATA tape drive signal cable. Important: Make sure that the cables avoid any fan connectors. Chapter 2. Installing optional devices 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
Installing
a
SATA
tape
drive
in
a
2.5-inch
model
server
To
install
a
tape
drive
in
a
2.5-inch
model
server,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
28.
2.
Turn
off
the
server
and
peripheral
devices,
and
disconnect
the
power
cords
and
all
external
cables.
Attention:
In
a
dc
power
environment,
only
trained
service
personnel
other
than
IBM
service
technicians
are
authorized
to
connect
or
disconnect
power
to
the
dc
power
supply.
See
the
documentation
that
comes
with
each
dc
power
supply.
3.
If
you
installed
the
space
filler
from
the
tape
enablement
kit
onto
the
tape-drive
assembly,
remove
it
now.
4.
Remove
the
server
cover.
5.
Remove
the
fan-bracket
assembly.
6.
Remove
the
filler
panel
from
the
tape-drive
bay.
7.
From
the
inside
of
the
server,
thread
the
tape-drive
end
of
the
cables
for
your
tape
drive
through
the
rear
of
the
tape-drive
bay
and
out
the
front
of
the
server.
8.
Connect
the
cable
or
cables
to
the
back
of
the
tape
drive.
9.
Push
the
tape-drive
assembly
into
the
tape-drive
bay,
gently
pulling
the
cables
farther
into
the
server
as
you
do
so,
until
the
tape-drive
assembly
stops.
10.
Push
the
tray
handle
to
the
closed
(locked)
position.
11.
Connect
the
cable
connectors
to
the
following
system-board
connectors
(see
“System-board
internal
cable
connectors”
on
page
19
for
the
location
of
the
connectors):
v
Signal
connector:
SATA
tape
drive
signal
connector,
J102
v
Power
connector:
tape-drive
power
connector,
J100
The
following
illustration
shows
the
routing
of
the
SATA
tape
drive
signal
cable.
Important:
Make
sure
that
the
cables
avoid
any
fan
connectors.
Chapter
2.
Installing
optional
devices
53