IBM 7979B1U User Manual - Page 64

-inch, drives, 5-inch, Attention

Get IBM 7979B1U PDF manuals and user guides View all IBM 7979B1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

v The server 2.5-inch models support eight 2.5-inch hot-swap hard disk drives installed on Ultra-Slim hard disk drive trays for 2.5-inch drives. For a list of supported 2.5-inch hard disk drives, see http://www.ibm.com/servers/eserver/ serverproven/compat/us/. v All hot-swap drives in the server should have the same throughput speed rating. Mixing hard disk drives with different speed ratings will cause all drives to operate at the lower throughput speed. v The ID that is assigned to each bay is printed on the front of the server. The following illustrations show how to install a hot-swap hard disk drive. 3.5-inch drives Filler panel Hard disk drive Tray handle 2.5-inch drives To install a drive in a hot-swap bay, complete the following steps. Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed in each bay. 1. Read the safety information that begins on page vii and "Installation guidelines" on page 28. 2. Remove the filler panel from one of the empty hot-swap bays. 48 System x3650 Type 7979: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
v
The
server
2.5-inch
models
support
eight
2.5-inch
hot-swap
hard
disk
drives
installed
on
Ultra-Slim
hard
disk
drive
trays
for
2.5-inch
drives.
For
a
list
of
supported
2.5-inch
hard
disk
drives,
see
serverproven/compat/us/.
v
All
hot-swap
drives
in
the
server
should
have
the
same
throughput
speed
rating.
Mixing
hard
disk
drives
with
different
speed
ratings
will
cause
all
drives
to
operate
at
the
lower
throughput
speed.
v
The
ID
that
is
assigned
to
each
bay
is
printed
on
the
front
of
the
server.
The
following
illustrations
show
how
to
install
a
hot-swap
hard
disk
drive.
3.5-inch
drives
Filler panel
Hard disk drive
Tray handle
2.5-inch
drives
To
install
a
drive
in
a
hot-swap
bay,
complete
the
following
steps.
Attention:
To
maintain
proper
system
cooling,
do
not
operate
the
server
for
more
than
10
minutes
without
either
a
drive
or
a
filler
panel
installed
in
each
bay.
1.
Read
the
safety
information
that
begins
on
page
vii
and
“Installation
guidelines”
on
page
28.
2.
Remove
the
filler
panel
from
one
of
the
empty
hot-swap
bays.
48
System
x3650
Type
7979:
User’s
Guide