IBM 7979B1U User Manual - Page 72

hook-and-loop-fastener

Get IBM 7979B1U PDF manuals and user guides View all IBM 7979B1U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

7. From the inside of the server, thread the tape-drive end of the cables through the slot in the left side of the hard disk drive cage and out the front of the server. Note: The terminator on the short section of the cable does not go through the slot; do not attempt to force it. 8. Connect the cables to the back of the tape drive. 9. Push the tape-drive assembly into the bays, gently pulling the cables farther into the server as you do so, until the tape-drive assembly stops. 10. Push the tray handle to the closed (locked) position. 11. Remove the backing from the terminator hook-and-loop fastener. With the hook-and-loop-fastener side down, orient the terminator as shown in the following illustration and press the terminator onto the top of the CD/DVD drive bay. SCSI terminator 12. Remove the riser-card assembly and the DIMM air baffle (see "Removing the riser-card assembly" on page 32 and "Removing the DIMM air baffle" on page 36). 13. Temporarily disconnect the hard disk drive backplane signal cable from the connector on the system board (J92), remove the cable from the cable clamp, and set the cable aside. See "System-board internal cable connectors" on page 19 for the location of the connector and cable clamp. 14. Route the SCSI signal cable to the supported SCSI adapter that is installed in slot 1 of the riser-card assembly, as shown in the following illustration. Make sure that the cable passes through the cable clamp. Important: Make sure that the cables avoid any fan connectors. 56 System x3650 Type 7979: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
7.
From
the
inside
of
the
server,
thread
the
tape-drive
end
of
the
cables
through
the
slot
in
the
left
side
of
the
hard
disk
drive
cage
and
out
the
front
of
the
server.
Note:
The
terminator
on
the
short
section
of
the
cable
does
not
go
through
the
slot;
do
not
attempt
to
force
it.
8.
Connect
the
cables
to
the
back
of
the
tape
drive.
9.
Push
the
tape-drive
assembly
into
the
bays,
gently
pulling
the
cables
farther
into
the
server
as
you
do
so,
until
the
tape-drive
assembly
stops.
10.
Push
the
tray
handle
to
the
closed
(locked)
position.
11.
Remove
the
backing
from
the
terminator
hook-and-loop
fastener.
With
the
hook-and-loop-fastener
side
down,
orient
the
terminator
as
shown
in
the
following
illustration
and
press
the
terminator
onto
the
top
of
the
CD/DVD
drive
bay.
SCSI terminator
12.
Remove
the
riser-card
assembly
and
the
DIMM
air
baffle
(see
“Removing
the
riser-card
assembly”
on
page
32
and
“Removing
the
DIMM
air
baffle”
on
page
36).
13.
Temporarily
disconnect
the
hard
disk
drive
backplane
signal
cable
from
the
connector
on
the
system
board
(J92),
remove
the
cable
from
the
cable
clamp,
and
set
the
cable
aside.
See
“System-board
internal
cable
connectors”
on
page
19
for
the
location
of
the
connector
and
cable
clamp.
14.
Route
the
SCSI
signal
cable
to
the
supported
SCSI
adapter
that
is
installed
in
slot
1
of
the
riser-card
assembly,
as
shown
in
the
following
illustration.
Make
sure
that
the
cable
passes
through
the
cable
clamp.
Important:
Make
sure
that
the
cables
avoid
any
fan
connectors.
56
System
x3650
Type
7979:
User’s
Guide