IBM 86645RY Hardware Maintenance Manual - Page 137

Installing a drive in a hot-swap bay, non-hot-swap bays, and the 16-bit 2-drop SCSI cable

Get IBM 86645RY - Netfinity 5600 - 5RY PDF manuals and user guides View all IBM 86645RY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 137 highlights

2. Remove the trim bezel. (See "Removing the trim bezel" on page 106.) 3. Remove the filler panel 2 from the bay opening by pulling the filler panel away from the server. You do not need the filler panel when you have a drive installed in the bay. 4. Touch the static-protective bag containing the drive to any unpainted metal surface on the server; then, remove the drive from the bag and place it on a static-protective surface. 5. Set any jumpers or switches on the drive according to the documentation that comes with the drive. 6. Install rails on the drive. If you are installing a standard-size drive: a. Pull the blue slide rails 3 off the back of the filler panel. b. Clip the rails onto the sides of the drive. If you are installing a digital linear tape (DLT) backup drive 1 , the slide rails 4 and screws are included in the country kit. 7. Place the drive so that the slide rails engage in the bay guide rails. Push the drive into the bay until it clicks into place. 8. If you have not already done so, install an optional SCSI adapter. (See "Working with adapters" on page 107 for information about installing an adapter.) See "SCSI drives" on page 126 for information about optional SCSI adapters, installation of drives in the non-hot-swap bays, and the 16-bit 2-drop SCSI cable that is provided for use with optional SCSI adapters. 9. Connect one of the connectors on the SCSI cable for the non-hot-swap drive bays to the back of the drive 1. 10. Connect a power cable to the back of the drive. Power cables for non-hot-swap drives come installed in the server. The connectors are keyed and can be inserted only one way. 11. If you are installing another non-hot-swap drive, do so at this time. Otherwise, continue with the next step. 12. If you have other options to install or remove, do so now; otherwise, go to "Completing the installation" on page 141. Installing a drive in a hot-swap bay: The hot-swap drive bays support hot-swap drives only. This section gives the procedure for installing a hot-swap hard disk drive. If you want to remove a drive, reverse the following steps. Netfinity 5600 - Type 8664 129

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
2.
Remove the trim bezel.
(See “Removing the trim
bezel” on page
106.)
3.
Remove the filler panel
±2²
from the bay opening by
pulling the filler panel away from the server.
You do
not need the filler panel when you have a drive
installed in the bay.
4.
Touch the static-protective bag containing the drive to
any unpainted metal surface on the server; then,
remove the drive from the bag and place it on a
static-protective surface.
5.
Set any jumpers or switches on the drive according to
the documentation that comes with the drive.
6.
Install rails on the drive.
±
If you are installing a standard-size drive:
a.
Pull the blue slide rails
±3²
off the back of
the filler panel.
b.
Clip the rails onto the sides of the drive.
±
If you are installing a digital linear tape (DLT)
backup drive
±1²
, the slide rails
±4²
and screws
are included in the country kit.
7.
Place the drive so that the slide rails engage in the
bay guide rails.
Push the drive into the bay until it
clicks into place.
8.
If you have not already done so, install an optional
SCSI adapter.
(See “Working with adapters” on
page
107 for information about installing an adapter.)
See “SCSI drives” on page
126 for information about
optional SCSI adapters, installation of drives in the
non-hot-swap bays, and the 16-bit 2-drop SCSI cable
that is provided for use with optional SCSI adapters.
9.
Connect one of the connectors on the SCSI cable for
the non-hot-swap drive bays to the back of the drive
±1²
.
10.
Connect a power cable to the back of the drive.
Power cables for non-hot-swap drives come installed
in the server.
The connectors are keyed and can be
inserted only one way.
11.
If you are installing another non-hot-swap drive, do so
at this time.
Otherwise, continue with the next step.
12.
If you have other options to install or remove, do so
now; otherwise, go to “Completing the installation” on
page 141.
Installing a drive in a hot-swap bay:
The
hot-swap drive bays support hot-swap drives only.
This section gives the procedure for installing a hot-swap
hard disk drive. If you want to remove a drive, reverse the
following steps.
Netfinity 5600 - Type 8664
129