IBM 86645RY Hardware Maintenance Manual - Page 187
to its new location, Move the power switch panel
 |
View all IBM 86645RY manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 187 highlights
e. Install two screws in the back of the cover. 7. Position the server open-side-up on a flat, nonconductive surface. 8. Remove the feet 1 from the server by unscrewing them. 9. Remove the fan assemblies at the front of the server. To remove a fan assembly, press the orange touchpoint1 to release the fan assembly; then, lift the fan assembly out. 10. Move the power switch panel 1 to its new location 2. a. Remove the hard disk drives and note the SCSI ID assigned to each drive. b. Remove the power switch panel by pressing down and in on the arrow on the top blue tab. 1 An orange touchpoint is a point on a hot-swap component where the component can be gripped, a latch moved, and so on. Netfinity 5600 - Type 8664 179
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182 -
183 -
184 -
185 -
186 -
187 -
188 -
189 -
190 -
191 -
192 -
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
 |
 |
e.
Install two screws in the back of the cover.
7.
Position the server open-side-up on a flat,
nonconductive surface.
8.
Remove the feet
±1²
from the server by unscrewing
them.
9.
Remove the fan assemblies at the front of the server.
To remove a fan assembly, press the orange
touchpoint
1
to release the fan assembly; then, lift the
fan assembly out.
10.
Move the power switch panel
±1²
to its new location
±2²
.
a.
Remove the hard disk drives and note the SCSI
ID assigned to each drive.
b.
Remove the power switch panel by pressing
down and in on the arrow on the top blue tab.
1
An orange touchpoint is a point on a hot-swap component
where the component can be gripped, a latch moved, and so
on.
Netfinity 5600 - Type 8664
179