IBM 86645RY Hardware Maintenance Manual - Page 144

DC Power light, and AC Power

Get IBM 86645RY - Netfinity 5600 - 5RY PDF manuals and user guides View all IBM 86645RY manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

7 DC Power light To add a power supply: 1. Remove the filler panel 2 from the empty power supply bay by inserting your finger into the depression on the filler panel and pulling it away from the server. Save the filler panel in case you remove the power supply at a later time. Note During normal operation, each power-supply bay must have either a power supply or filler panel installed for proper cooling. 2. Install the power supply 1 in the bay: a. Place the handle 5 on the power supply in the open position (that is, perpendicular to the power supply) and slide the power supply into the chassis. b. Gently close the handle to seat the power supply in the bay. 3. Plug the power cord for the added power supply into the power cord connector 2 . 4. Route the power cord through the cable-restraint bracket 3 . 5. Plug the power cord into a properly grounded electrical outlet. 6. Verify that the DC Power light 7 and AC Power light 6 on the power supply are lit, indicating that the power supply is operating correctly. 7. If you have other options to install or remove, do so now; otherwise, go to "Completing the installation" on page 141. 136 Netfinity Server HMM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
±7²
DC Power light
To add a power supply:
1.
Remove the filler panel
±2²
from the empty power
supply bay by inserting your finger into the depression
on the filler panel and pulling it away from the server.
Save the filler panel in case you remove the power
supply at a later time.
Note
During normal operation, each power-supply bay
must have either a power supply or filler panel
installed for proper cooling.
2.
Install the power supply
±1²
in the bay:
a.
Place the handle
±5²
on the power supply in the
open position (that is, perpendicular to the power
supply) and slide the power supply into the
chassis.
b.
Gently close the handle to seat the power supply
in the bay.
3.
Plug the power cord for the added power supply into
the power cord connector
±2²
.
4.
Route the power cord through the cable-restraint
bracket
±3²
.
5.
Plug the power cord into a properly grounded
electrical outlet.
6.
Verify that the DC Power light
±7²
and AC Power
light
±6²
on the power supply are lit, indicating that
the power supply is operating correctly.
7.
If you have other options to install or remove, do so
now; otherwise, go to “Completing the installation” on
page 141.
136
Netfinity Server HMM