Icom ID-880H Instruction Manual - Page 120

Full/band/programmed scan

Get Icom ID-880H PDF manuals and user guides View all Icom ID-880H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

8 SCAN OPERATION Full/band/programmed scan q Push [VFO/MHz] to select the VFO mode. • Select the desired frequency band with [BAND] and [DIAL], if desired. w Set the squelch level. e Push and hold [SCAN](VFO/MHz) for 1 sec. to enter the scanning type selection. r Rotate [DIAL] to select the desired scanning type. • "ALL" for full scan; "BAND" for band scan, "P-LINK x (or program scan link name if programmed)" for programmed link scan (x= 0 to 9), "PROGxx (or scan name if programmed)" for programmed scan (xx= 0 to 24; only programmed scan edge numbers are displayed), "DUP" (appears only when duplex operation is set) for duplex scan, "TONE" (appears only when the subaudible tone, tone squelch or DTCS squelch is set) for tone scan. [DIAL] [SCAN] Full scan Push and hold [SCAN] for 1 sec., then rotate [DIAL]. Programmed link scan Band scan Selectable from "0" to "9." Programmed scan Selectable from "0" to "24" if programmed. 102 t Push [SCAN](VFO/MHz) to start the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction. This also causes the transceiver to resume scanning. • Push [SCAN](VFO/MHz) to stop the scan. During full/band scan During programmed scan About the scanning steps: The selected tuning step in each frequency band (in the VFO mode) is used during scan. Duplex scan function: Repeatedly scans two frequencies (transmission/reception) during duplex scan operation. Scan name can be displayed instead of "P-LINK x" for program link scan (x= 0 to 9), "PROGxx" for programmed scan (xx= 0 to 24) when scan name is programmed and set to ON in the DISP set mode. MENU ¶ SET ¶ DISP ¶ SCAN N (p. 132) (Push [MENU ]), (rotate [DIAL], then push [ ](MONI).) Scan name is not displayed during scan.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
8
SCAN OPERATION
±
Full/band/programmed scan
q
Push
[VFO/MHz]
to select the VFO mode
.
•
Select the desired frequency band with
[BAND]
and
[DIAL]
, if
desired.
w
Set the squelch level.
e
Push and hold
[SCAN]
(VFO/MHz) for 1 sec. to enter the
scanning type selection.
r
Rotate
[DIAL]
to select the desired scanning type.
•
“ALL” for full scan; “BAND” for band scan, “P-LINK x (or program
scan link name if programmed)” for programmed link scan (x= 0
to 9), “PROGxx (or scan name if programmed)” for programmed
scan (xx= 0 to 24; only programmed scan edge numbers are dis-
played), “DUP” (appears only when duplex operation is set) for
duplex scan, “TONE” (appears only when the subaudible tone,
tone squelch or DTCS squelch is set) for tone scan.
[DIAL]
[SCAN]
Full scan
Band scan
Programmed link scan
Push and hold
[SCAN]
for 1 sec.,
then rotate
[DIAL]
.
Programmed scan
Selectable from “0” to “9.”
Selectable from “0” to “24” if programmed.
t
Push
[SCAN]
(VFO/MHz) to start the scan.
• Scan pauses when a signal is received.
•
Rotate
[DIAL]
to change the scanning direction. This also
causes the transceiver to resume scanning.
• Push
[SCAN]
(VFO/MHz) to stop the scan.
About the scanning steps:
The selected tuning step in
each frequency band (in the VFO mode) is used during
scan.
Duplex scan function:
Repeatedly scans two frequencies
(transmission/reception) during duplex scan operation.
Scan name can be displayed instead of “P-LINK x” for pro-
gram link scan (x= 0 to 9), “PROGxx” for programmed scan
(xx= 0 to 24) when scan name is programmed and set to ON
in the DISP set mode.
MENU
SET
DISP
SCAN N
(p. 132)
(Push
[MENU
]
), (rotate
[DIAL]
, then push
[
]
(MONI).)
Scan name is not displayed during scan.
During full/band scan
During programmed scan
102