Icom ID-880H Instruction Manual - Page 123

Memory scan

Get Icom ID-880H PDF manuals and user guides View all Icom ID-880H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 123 highlights

SCAN OPERATION 8 Memory scan IMPORTANT: To perform memory scan, 2 or more memory channels MUST be programmed, otherwise the scan will not start. q Push [M/CALL] several times to select the memory mode. w Set the squelch level. e Push and hold [SCAN](VFO/MHz) for 1 sec. to enter the scanning type selection. r Rotate [DIAL] to select the desired scanning type. • "ALL" for all memory scan; "BAND" for band memory scan, "MODE" for mode scan, "DUP" (appears only when duplex operation is set) for duplex scan, "TONE" (appears only when the subaudible tone, tone squelch or DTCS squelch is set) for tone scan. Push and hold [SCAN] for 1 sec., [DIAL] [SCAN] then rotate [DIAL]. All memory scan Mode scan Band memory scan Selected mode is displayed. Duplex scan t Push [SCAN](VFO/MHz) to start the scan. • Scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction. This also causes the transceiver to resume scanning. • Push [SCAN](VFO/MHz) to stop the scan. During memory scan During mode scan 8 Band memory scan function: Repeatedly scans all memory channels programmed with any frequencies of the band programmed in the memory channel selected for scanning. Mode scan function: Repeatedly scans all memory channels in which the same operating mode as the selected memory channel has been programmed. Duplex scan function: Repeatedly scans two frequencies (transmission/reception) during duplex scan operation. 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
105
8
SCAN OPERATION
±
Memory scan
IMPORTANT:
To perform memory scan, 2 or more mem-
ory channels MUST be programmed, otherwise the scan
will not start.
q
Push
[M/CALL]
several times to select the memory mode.
w
Set the squelch level.
e
Push and hold
[SCAN]
(VFO/MHz) for 1 sec. to enter the
scanning type selection.
r
Rotate
[DIAL]
to select the desired scanning type.
•
“ALL” for all memory scan; “BAND” for band memory scan,
“MODE” for mode scan, “DUP” (appears only when duplex op-
eration is set) for duplex scan, “TONE” (appears only when the
subaudible tone, tone squelch or DTCS squelch is set) for tone
scan.
[DIAL]
[SCAN]
All memory scan
Band memory scan
Mode scan
Push and hold
[SCAN]
for 1 sec.,
then rotate
[DIAL]
.
Duplex scan
Selected mode is displayed.
t
Push
[SCAN]
(VFO/MHz) to start the scan.
• Scan pauses when a signal is received.
•
Rotate
[DIAL]
to change the scanning direction. This also
causes the transceiver to resume scanning.
• Push
[SCAN]
(VFO/MHz) to stop the scan.
Band memory scan function:
Repeatedly scans all
memory channels programmed with any frequencies of
the band programmed in the memory channel selected for
scanning.
Mode scan function:
Repeatedly scans all memory chan-
nels in which the same operating mode as the selected
memory channel has been programmed.
Duplex scan function:
Repeatedly scans two frequencies
(transmission/reception) during duplex scan operation.
During memory scan
During mode scan
8