Sony STR-DN1040 Operating Instructions (Large File - 14.3 MB) - Page 94

To check the Auto Calibration, results, When error code appears, When warning message appears

Get Sony STR-DN1040 PDF manuals and user guides View all Sony STR-DN1040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Tips • You can change the unit of distance in "Distance Unit" in the Speaker Settings menu (page 97). • The size of a speaker ("Large"/"Small") is determined by the low frequency characteristics. The measurement results may vary, depending on the position of the optimizer microphone and speakers, and the shape of the room. It is recommended that you apply the measurement results. However, you can change those settings in the Speaker Settings menu. Save the measurement results first, then try to change the settings. To check the Auto Calibration results To check error code or warning message obtained in "Auto Calibration" (page 94), proceed with the following steps. When error code appears Check the error and perform Auto Calibration again. 1 Select "Retry", then press . 2 Repeat steps 1 to 3 in "Auto Calibration" (page 93). When warning message appears Check the warning message and select "Ok". Message list after Auto Calibration measurement Display and explanation Code 30 Headphones are connected to the PHONES jack on the receiver. Remove the headphones and perform the Auto Calibration again. Code 31 The SPEAKERS is set to off. Set to other speaker settings and perform the Auto Calibration again. Display and explanation Code 32 Code 33 Speakers were not detected or not connected properly. • None of the front speakers are connected or only one front speaker is connected. • Either the surround left or surround right speaker is not connected. • Surround back speakers or front high speakers are connected even though surround speakers are not connected. Connect the surround speaker(s) to the SPEAKERS SURROUND terminals. • The surround back speaker is connected only to the SPEAKERS SURROUND BACK/BI-AMP/FRONT HIGH/FRONT B R terminals. When you connect only one surround back speaker, connect it to the SPEAKERS SURROUND BACK/ BI-AMP/FRONT HIGH/FRONT B L terminals. • Either the front high left or front high right speaker is not connected. The optimizer microphone is not connected. Make sure that the optimizer microphone is connected properly and perform the Auto Calibration again. If the optimizer microphone is connected properly but the error code still appears, the optimizer microphone cable may be damaged. Warning 40 The measurement process has completed with high noise level detection. You may be able to achieve better results if you try in a quiet environment again. Warning 41 Warning 42 The input from the microphone is too big. • The distance between the speaker and the microphone may be too close. Set them apart and perform the measurement again. Warning 43 The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the measurement in a quiet environment. 94US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
94
US
•
You can change the unit of distance in “Distance
Unit” in the Speaker Settings menu (page 97).
• The size of a speaker (“Large”/“Small”) is
determined by the low frequency
characteristics. The measurement results may
vary, depending on the position of the optimizer
microphone and speakers, and the shape of the
room. It is recommended that you apply the
measurement results. However, you can change
those settings in the Speaker Settings menu.
Save the measurement results first, then try to
change the settings.
To check the Auto Calibration
results
To check error code or warning message
obtained in “Auto Calibration” (page 94),
proceed with the following steps.
When error code appears
Check the error and perform Auto
Calibration again.
1
Select “Retry”, then press
2
Repeat steps 1 to 3 in “Auto
Calibration” (page 93).
When warning message appears
Check the warning message and select
“Ok”.
Message list after Auto
Calibration measurement
Tips
Display and explanation
Code 30
Headphones are connected to the PHONES
jack on the receiver. Remove the headphones
and perform the Auto Calibration again.
Code 31
The SPEAKERS is set to off. Set to other
speaker settings and perform the Auto
Calibration again.
Code 32
Code 33
Speakers were not detected or not connected
properly.
•
None of the front speakers are connected or
only one front speaker is connected.
•
Either the surround left or surround right
speaker is not connected.
•
Surround back speakers or front high
speakers are connected even though
surround speakers are not connected.
Connect the surround speaker(s) to the
SPEAKERS SURROUND terminals.
•
The surround back speaker is connected
only to the SPEAKERS SURROUND
BACK/BI-AMP/FRONT HIGH/FRONT
B R terminals. When you connect only one
surround back speaker, connect it to the
SPEAKERS SURROUND BACK/
BI-AMP/FRONT HIGH/FRONT B L
terminals.
•
Either the front high left or front high right
speaker is not connected.
The optimizer microphone is not connected.
Make sure that the optimizer microphone is
connected properly and perform the Auto
Calibration again.
If the optimizer microphone is connected
properly but the error code still appears, the
optimizer microphone cable may be
damaged.
Warning 40
The measurement process has completed with
high noise level detection. You may be able to
achieve better results if you try in a quiet
environment again.
Warning 41
Warning 42
The input from the microphone is too big.
•
The distance between the speaker and the
microphone may be too close. Set them
apart and perform the measurement again.
Warning 43
The distance and position of a subwoofer
cannot be detected. This may be caused by
noise. Try to perform the measurement in a
quiet environment.
Display and explanation