Home » IBM Manuals » Desktops » IBM 8862 » Manual Viewer

IBM 8862 Hardware Maintenance Manual - Page 16

power, Ethernet, Remote, Supervisor, Adapter, activity, Attention, Locator

UPC - 000435172679

Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Rear view The following illustration shows the LEDs on the rear of the server. AC power LED Ethernet link LED Remote Supervisor Adapter II activity LED AC AC Remote Supervisor Adapter II power LED Ethernet activity LED Locator LED Attention LED AC power LED: Each hot-swap power supply has an ac power LED that is visible from the rear of the server. The power supply also has an ac power LED and a dc power LED on the top of the power supply, visible when the server cover is removed. When the ac power LED is lit, ac input to the power module is present and within specifications. During typical operation, both the ac and dc power LEDs on the top of the power supply are lit. For any other combination of LEDs, see "Power LED errors" on page 130. Ethernet link LEDs: When these LEDs (one for the Remote Supervisor Adapter II, two for the network) are lit, they indicate that the related Ethernet link is operational. Remote Supervisor Adapter II activity LED: When this LED is flashing, the Remote Supervisor Adapter II is functioning normally. When the LED is lit continuously, there is a problem with the Remote Supervisor Adapter II. When the LED is off, the Remote Supervisor Adapter II is not functioning. Remote Supervisor Adapter II power LED: When this LED is lit, it indicates that power is being supplied to the Remote Supervisor Adapter II. Attention LED: When this LED is on steady, it indicates that the adapter in the corresponding slot is ready to be removed (hot-pluggable adapter only) or there is a problem with the adapter. When this LED is flashing, it indicates that an operation is in progress or that the adapter requires attention, depending on the operating system. Locator LED: Use this blue LED to visually locate the server if it is in a location with numerous other servers. A locator LED is also on the operation information panel on the front of the server. You can use the Management Processor Assistant (MPA) in IBM Director to cause this LED to be lit, off, or flashing (see the User's Guide on the IBM xSeries Documentation CD for more information on IBM Director). If the server is connected to an RXE-100 Remote Expansion Enclosure, pressing the Locate button on the enclosure causes this LED to be lit. Note: This LED flashes while the server is being turned on or restarted, and turns off when POST is complete. 6 IBM xSeries 365 Types 8861, 8862: Hardware Maintenance Manual and Troubleshooting Guide

Section	Page
About this manual	5
Important safety information	5
Online support	5
Contents	7
Chapter 1. Introduction	11
Related publications	11
Notices and statements used in this publication	12
Features and specifications	13
Server controls, LEDs, and power	14
Front view	14
Rear view	16
Light path diagnostics LED panel	18
Server power features	18
Turning on the server	18
Turning off the server	19
Chapter 2. Configuring the server	21
Using the Configuration/Setup Utility program	21
Using the ServerGuide Setup and Installation CD	22
Using the PXE boot agent utility program	22
Using the RAID configuration programs	23
Updating the integrated service processor firmware	23
Configuring the Gigabit Ethernet controllers	23
Remote Supervisor Adapter II	23
Chapter 3. Diagnostics	25
General checkout	25
Diagnostic tools overview	27
POST error logs	27
Viewing error logs from the Configuration/Setup Utility program	27
Viewing error logs from the diagnostic programs	28
Light path diagnostics	28
Microprocessor LEDs	29
DIMM LEDs	30
Remind button	31
Diagnostic programs and error messages	32
Diagnostic text messages	32
Starting the diagnostic programs	33
Viewing the test log	33
Viewing the system-error log	34
Recovering BIOS code	34
Password override jumper	35
Forcing a power-on	36
Power checkout	37
Ethernet controller troubleshooting	37
Chapter 4. Installing options	39
Installation guidelines	39
System reliability guidelines	39
Working inside a server with power on	40
Handling static-sensitive devices	40
Major components of the xSeries 365 server	41
Removing the cover and bezel	42
PCI or PCI-X adapters	43
Installing a PCI or PCI-X adapter	45
Removing a PCI or PCI-X adapter	46
Installing a hot-swap hard disk drive	46
Replacing the CD-ROM drive	48
Memory modules	49
DIMM banks and ports	50
DIMM installation	51
Installing a microprocessor	54
Installing a hot-swap power supply	61
Replacing the battery	63
Replacing a hot-swap fan	65
Replacing the memory cassette	66
Completing the installation	68
Installing the cover and bezel	68
Connecting the cables	69
RXE connector cabling	70
Gigabit Ethernet cabling	70
Updating the server configuration	70
I/O connectors	71
Server connectors	72
Remote Supervisor Adapter II connectors	72
Ethernet connector	73
Universal Serial Bus connector	73
RXE Expansion Port connector	74
Auxiliary-device (pointing device) connector	74
Keyboard connector	74
Serial connector	74
RXE Management Port connector	74
Power supply connector	75
SCSI connector	75
Chapter 5. FRU information (service only)	77
Microprocessor tray assembly	78
Microprocessor board connectors, jumpers and LEDs	78
Microprocessor removal	78
Thermal grease	79
Diskette drive	81
Operator information panel	82
Media interposer card	83
SCSI backplane	84
PCI switch card assembly	86
Adapter retainer bracket assembly	87
Power-supply structure	88
I/O board and power backplane assembly	89
I/O board connectors	89
I/O board LEDs	90
I/O board switches and jumpers	90
Replacing the I/O board and power backplane assembly	91
Chapter 6. Symptom-to-FRU index	95
Beep symptoms	96
No beep symptoms	97
POST error codes	98
Light path LED errors	103
Diagnostic error codes	105
System-error log entries	115
SMI handler messages	116
Service processor messages	119
Error symptoms	131
Power LED errors	140
SCSI error messages	142
ServeRAID (ISPR) error procedures	142
ServeRAID error codes	144
Undetermined problems	146
Problem-determination tips	147
Chapter 7. Parts listing, Types 8861, 8862	149
System	150
Keyboard CRUs	151
Power cord FRUs	152
Appendix A. Getting help and technical assistance	155
Before you call	155
Using the documentation	155
Getting help and information from the World Wide Web	155
Software service and support	156
Hardware service and support	156
Appendix B. Related service information	157
Safety information	157
General safety	157
Electrical safety	158
Safety inspection guide	159
Handling electrostatic discharge-sensitive devices	160
Grounding requirements	160
Safety notices (multilingual translations)	160
Appendix C. Notices	201
Edition notice	201
Trademarks	202
Important notes	202
Product recycling and disposal	203
Battery return program	203
Electronic emission notices	204
Federal Communications Commission (FCC) statement	204
Industry Canada Class A emission compliance statement	204
Australia and New Zealand Class A statement	204
United Kingdom telecommunications safety requirement	204
European Union EMC Directive conformance statement	205
Taiwanese Class A warning statement	205
Chinese Class A warning statement	205
Japanese Voluntary Control Council for Interference (VCCI) statement	205

Match case Limit results 1 per page

Rear

view

The

following

illustration

shows

the

LEDs

the

rear

the

server.

AC power LED

Locator LED

Attention LED

Ethernet

link LED

Ethernet

activity LED

Remote Supervisor

Adapter II activity LED

Remote Supervisor

Adapter II power LED

power

LED:

Each

hot-swap

power

supply

has

power

LED

that

visible

from

the

rear

the

server.

The

power

supply

also

has

power

LED

and

power

LED

the

top

the

power

supply,

visible

when

the

server

cover

removed.

When

the

power

LED

lit,

input

the

power

module

present

and

within

specifications.

During

typical

operation,

both

the

and

power

LEDs

the

top

the

power

supply

are

lit.

For

any

other

combination

LEDs,

see

“Power

LED

errors”

page

130.

Ethernet

link

LEDs:

When

these

LEDs

(one

for

the

Remote

Supervisor

Adapter

II,

two

for

the

network)

are

lit,

they

indicate

that

the

Ethernet

link

operational.

Remote

Supervisor

Adapter

activity

LED:

When

this

LED

flashing,

the

Remote

Supervisor

Adapter

functioning

normally.

When

the

LED

lit

continuously,

there

problem

with

the

Remote

Supervisor

Adapter

II.

When

the

LED

off,

the

Remote

Supervisor

Adapter

not

functioning.

Remote

Supervisor

Adapter

power

LED:

When

this

LED

lit,

indicates

that

power

being

supplied

the

Remote

Supervisor

Adapter

II.

Attention

LED:

When

this

LED

steady,

indicates

that

the

adapter

the

corresponding

slot

ready

removed

(hot-pluggable

adapter

only)

there

problem

with

the

adapter.

When

this

LED

flashing,

indicates

that

operation

progress

that

the

adapter

requires

attention,

depending

the

operating

system.

Locator

LED:

Use

this

blue

LED

visually

locate

the

server

location

with

numerous

other

servers.

locator

LED

also

the

operation

information

panel

the

front

the

server.

You

can

use

the

Management

Processor

Assistant

(MPA)

IBM

Director

cause

this

LED

lit,

off,

flashing

(see

the

User’s

Guide

the

IBM

xSeries

Documentation

for

information

IBM

Director).

the

server

connected

RXE-100

Remote

Expansion

Enclosure,

pressing

the

Locate

button

the

enclosure

causes

this

LED

lit.

Note:

This

LED

flashes

while

the

server

being

turned

restarted,

and

turns

off

when

POST

complete.

IBM

xSeries

365

Types

8861,

8862:

Hardware

Maintenance

Manual

and

Troubleshooting

Guide