Home » Kyocera Manuals » Printers » Kyocera FS-1128MFP » Manual Viewer

Kyocera FS-1128MFP Service Manual - Page 128

Control PWB - Operation panel PWB, panel PWB YC1 - waste toner

Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

2JN Code 6030 6400 7990 F000 Contents Causes Remarks Check procedures/corrective measures Broken fuser thermistor wire Input from fuser thermistor is 0 (A/D value). Poor contact in the fuser thermistor connector terminals. Reinsert the connector (See page 1-5-34). Broken fuser ther- Replace the fuser unit (See page 1-5-34). mistor wire. Fuser thermistor installed incorrectly. Replace the fuser unit (See page 1-5-34). Fuser thermal cut- Replace the fuser unit (See page 1-5-34). out triggered. Fuser heater lamp Replace the fuser unit (See page 1-5-34). installed incorrectly. Broken fuser Replace the fuser unit (See page 1-5-34). heater lamp wire. Zero cross signal error The zero cross signal does not reach the control PWB for specified time. Defective harness between high voltage PWB (YC202) and control PWB (YC23), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness (See page 15-39). Defective connection between power source PWB (YC103) and high voltage PWB (YC201). Reinsert the connector. Defective power source PWB. Replace the power source PWB (See page 1-5-42). Defective control PWB. Replace the control PWB (See page 1-539). Waste toner full The waste toner sensor has detected that the waste toner reservoir (drum unit) is full. Waste toner reservoir (drum unit) is full. Defective waste toner sensor. Turn the main power switch off/on to restart the machine. If the error is not resolved, replace the drum unit (See page 1-5-30). Replace the waste toner sensor. Defective control PWB. Replace the control PWB (See page 1-539). Control PWB - Operation panel PWB communication error Defective harness between operation panel PWB (YC1) and control PWB (YC7), or improper connector insertion. Reinsert the connector. Also check for continuity within the connector harness. If none, remedy or replace the harness. Defective operation panel PWB. Replace the operation panel PWB. Defective control PWB. Replace the control PWB (See page 1-539). 1-4-10

Section	Page
Cover	1
Revision history	3
Safety precautions	5
CONTENTS	11
Specifications	15
1-1-1 Specifications	15
1-1-2 Parts names	18
(1) Overall	18
(2) Operation panel	19
1-1-3 Machine cross section	20
Installation	23
1-2-1 Installation environment	23
1-2-2 Unpacking	24
(1) Unpacking	24
(2) Removing the tapes	25
1-2-3 Installing the expansion memory (option)	28
Maintenance Mode	29
1-3-1 Maintenance mode	29
(1) Executing a maintenance item	29
(2) Maintenance modes item list	30
(3) Contents of the maintenance mode items	34
1-3-2 Management mode	103
(1) Using the management mode	103
(2) Common Settings	104
(3) Copy Settings	108
(4) Sending Settings	108
(5) Document Box Settings	108
(6) Printer Settings	109
(7) Printing Reports/Sending Notice	109
(8) Adjustment/Maintenance	110
(9) Date/Timer	110
(10) Editing Destination (Address Book/Adding One- Touch Keys)	111
(11) Restarting the System	112
(12) Network Setup	112
(13) User Login Administration	114
(14) Job accounting	114
(15) FAX Settings	116
Troubleshooting	119
1-4-1 Paper misfeed detection	119
(1) Paper misfeed indication	119
(2) Paper misfeed detection condition	120
1-4-2 Self-diagnostic function	121
(1) Self-diagnostic function	121
(2) Self diagnostic codes	122
1-4-3 Image formation problems	130
(1) Completely blank printout.	131
(2) All-black printout.	131
(3) Dropouts.	132
(4) Black dots.	132
(5) Black horizontal streaks.	132
(6) Black vertical streaks.	133
(7) Unsharpness.	133
(8) Gray background.	133
(9) Dirt on the top edge or back of the paper.	134
(10) Undulated printing at the right edge (scanning start position).	134
1-4-4 Electric problems	135
1-4-5 Mechanical problems	138
1-4-6 Error codes	139
(1) Error code	139
(2) Table of general classification	140
(2-1) U004XX error code table: Interrupted phase B	142
(2-2) U006XX error code table: Problems with the unit	143
(2-3) U008XX error code table: Page transmission error	143
(2-4) U009XX error code table: Page reception error	143
(2-5) U010XX error code table: G3 transmission	144
(2-6) U011XX error code table: G3 reception	146
(2-7) U017XX error code table: V.34 transmission	148
(2-8) U018XX error code table: V.34 reception	148
(2-9) U023XX error code table: Relay command abnormal reception	148
(2-10) U044XX error code table: Encrypted transmission	148
1-4-7 Send error code	149
(1) Scan to SMB error codes	149
(2) Scan to FTP error codes	150
(3) Scan to E-mail error codes	151
(4) Network Twain error codes	152
(5) Software trouble error codes	152
Assembly and Disassembly	153
1-5-1 Precautions for assembly and disassembly	153
(1) Precautions	153
(2) Drum	153
(3) Toner	153
(4) How to tell a genuine Kyocera Mita toner container	154
1-5-2 Outer covers	155
(1) Detaching and refitting the left cover and right cover	155
1-5-3 Paper feed section	158
(1) Detaching and refitting the paper feed assembly (paper feed roller and pickup roller)	158
(2) Detaching and refitting the retard roller assembly	160
(3) Detaching and refitting the MP paper feed roller	162
(4) Note on removing and Installing the upper registration roller and lower registration roller	164
1-5-4 Optical section	165
(1) Detaching and refitting the DP	165
(2) Detaching and refitting the scanner unit	166
(3) Detaching and refitting the laser scanner unit (LSU)	169
(4) Replacing the image scanner unit (ISU)	173
(5) Detaching and refitting the exposure lamp and inverter PWB	179
1-5-5 Developing section	181
(1) Detaching and refitting the developing unit	181
1-5-6 Drum section	182
(1) Detaching and refitting the drum unit	182
(2) Detaching and refitting the main charger unit	183
1-5-7 Transfer/separation section	184
(1) Detaching and refitting the transfer roller	184
1-5-8 Fuser section	186
(1) Detaching and refitting the fuser unit	186
(2) Switching the fuser pressure	190
1-5-9 PWBs	191
(1) Detaching and refitting the control PWB	191
(2) Detaching and refitting the power source PWB	194
(3) Detaching and refitting the high voltage PWB	197
(4) Detaching and refitting the scanner PWB	201
(5) Detaching and refitting the FAX PWB	202
1-5-10 Others	203
(1) Detaching and refitting the main motor	203
(2) Direction of installing the left cooling fan motor, right cooling fan motor and power source fan motor	204
1-5-11 DP	205
Requirements on PWB Replacement	207
1-6-1 Upgrading the firmware	207
1-6-2 Remarks on control PWB replacement	208
Mechanical Construction	209
2-1-1 Paper feed/conveying section	209
(1) Cassette paper feed section	209
(2) MP tray paper feed section	210
(3) Paper conveying section	211
2-1-2 Drum section	212
(1) Drum section	212
(2) Main charger unit	213
2-1-3 Optical section	214
(1) Scanner unit	214
(2) Image scanner unit (ISU)	215
(3) Laser scanner unit	217
2-1-4 Developing section	219
2-1-5 Transfer/separation section	220
2-1-6 Cleaning section	221
2-1-7 Fuser section	222
2-1-8 Paper exit section	224
2-1-9 Duplex/conveying section	226
2-1-10 DP section	227
Electrical Parts Layout	229
2-2-1 Electrical parts layout	229
(1) PWBs	229
(2) Switches and sensors	231
(3) Other electrical components	232
(4) DP	233
Operation of the PWBs	235
2-3-1 Power source PWB	235
2-3-2 Control PWB	237
2-3-3 Scanner PWB	243
2-3-4 DP driver PWB	246
Appendixes	247
2-4-1 Appendixes	247
(1) Wiring diagram	247
(2) Repetitive defects gauge	249

Match case Limit results 1 per page

2JN

1-4-10

6030

Broken fuser thermistor wire

Input from fuser thermistor is 0 (A/D

value).

Poor contact in the

fuser thermistor

connector termi-

nals.

Reinsert the connector (See page 1-5-34).

Broken fuser ther-

mistor wire.