Home » Kyocera Manuals » Printers » Kyocera FS-1128MFP » Manual Viewer

Kyocera FS-1128MFP Service Manual - Page 144

(2-5) U010XX error code table: G3 transmission

Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

2JN (2-5) U010XX error code table: G3 transmission Error code U01000 U01001 U01010 U01011 U01012 U01013 U01014 U01015 U01016 U01017 U01018 U01019 U01020 U01021 U01022 U01023 U01024 U01025 U01026 U01027 U01028 U01040 U01041 U01042 Description An FTT signal was received for a set number of times after TCF signal transmission at 2400 bps. Or, an RTN signal was received in response to a Q signal (excluding EOP) after transmission at 2400 bps. Function of the unit differs from that indicated by a DIS signal. No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset number of command retransfers was exceeded (between units of our make). No relevant signal was received after transmission of a DCS, TCF signal, and the preset number of command retransfers was exceeded. No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset number of command retransfers was exceeded (between units of our make). No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number of command retransfers was exceeded (between units of our make). No relevant signal was received after transmission of an MPS signal, and the preset number of command retransfers was exceeded. No relevant signal was received after transmission of an EOM signal, and the preset number of command retransfers was exceeded. An MCF signal was received but no DIS signal was received after transmission of an EOM signal, and T1 timeout was detected. No relevant signal was received after transmission of an EOP signal, and the preset number of command retransfers was exceeded. No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of command retransfers was exceeded. No relevant signal was received after transmission of a CNC signal, and the preset number of command retransfers was exceeded (between units of our make). No relevant signal was received after transmission of a CTC signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of an EOR.Q signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of an RR signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of a PSS.NULL signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of a PSS.MPS signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of command retransfers was exceeded (ECM). No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset number of command retransfers was exceeded (ECM). T5 time-out was detected during ECM transmission (ECM). A DCN or other inappropriate signal was received during standby for DIS signal reception. A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of our make). A DCN signal was received after transmission of a DCS, TCF signal. 1-4-26

Section	Page
Cover	1
Revision history	3
Safety precautions	5
CONTENTS	11
Specifications	15
1-1-1 Specifications	15
1-1-2 Parts names	18
(1) Overall	18
(2) Operation panel	19
1-1-3 Machine cross section	20
Installation	23
1-2-1 Installation environment	23
1-2-2 Unpacking	24
(1) Unpacking	24
(2) Removing the tapes	25
1-2-3 Installing the expansion memory (option)	28
Maintenance Mode	29
1-3-1 Maintenance mode	29
(1) Executing a maintenance item	29
(2) Maintenance modes item list	30
(3) Contents of the maintenance mode items	34
1-3-2 Management mode	103
(1) Using the management mode	103
(2) Common Settings	104
(3) Copy Settings	108
(4) Sending Settings	108
(5) Document Box Settings	108
(6) Printer Settings	109
(7) Printing Reports/Sending Notice	109
(8) Adjustment/Maintenance	110
(9) Date/Timer	110
(10) Editing Destination (Address Book/Adding One- Touch Keys)	111
(11) Restarting the System	112
(12) Network Setup	112
(13) User Login Administration	114
(14) Job accounting	114
(15) FAX Settings	116
Troubleshooting	119
1-4-1 Paper misfeed detection	119
(1) Paper misfeed indication	119
(2) Paper misfeed detection condition	120
1-4-2 Self-diagnostic function	121
(1) Self-diagnostic function	121
(2) Self diagnostic codes	122
1-4-3 Image formation problems	130
(1) Completely blank printout.	131
(2) All-black printout.	131
(3) Dropouts.	132
(4) Black dots.	132
(5) Black horizontal streaks.	132
(6) Black vertical streaks.	133
(7) Unsharpness.	133
(8) Gray background.	133
(9) Dirt on the top edge or back of the paper.	134
(10) Undulated printing at the right edge (scanning start position).	134
1-4-4 Electric problems	135
1-4-5 Mechanical problems	138
1-4-6 Error codes	139
(1) Error code	139
(2) Table of general classification	140
(2-1) U004XX error code table: Interrupted phase B	142
(2-2) U006XX error code table: Problems with the unit	143
(2-3) U008XX error code table: Page transmission error	143
(2-4) U009XX error code table: Page reception error	143
(2-5) U010XX error code table: G3 transmission	144
(2-6) U011XX error code table: G3 reception	146
(2-7) U017XX error code table: V.34 transmission	148
(2-8) U018XX error code table: V.34 reception	148
(2-9) U023XX error code table: Relay command abnormal reception	148
(2-10) U044XX error code table: Encrypted transmission	148
1-4-7 Send error code	149
(1) Scan to SMB error codes	149
(2) Scan to FTP error codes	150
(3) Scan to E-mail error codes	151
(4) Network Twain error codes	152
(5) Software trouble error codes	152
Assembly and Disassembly	153
1-5-1 Precautions for assembly and disassembly	153
(1) Precautions	153
(2) Drum	153
(3) Toner	153
(4) How to tell a genuine Kyocera Mita toner container	154
1-5-2 Outer covers	155
(1) Detaching and refitting the left cover and right cover	155
1-5-3 Paper feed section	158
(1) Detaching and refitting the paper feed assembly (paper feed roller and pickup roller)	158
(2) Detaching and refitting the retard roller assembly	160
(3) Detaching and refitting the MP paper feed roller	162
(4) Note on removing and Installing the upper registration roller and lower registration roller	164
1-5-4 Optical section	165
(1) Detaching and refitting the DP	165
(2) Detaching and refitting the scanner unit	166
(3) Detaching and refitting the laser scanner unit (LSU)	169
(4) Replacing the image scanner unit (ISU)	173
(5) Detaching and refitting the exposure lamp and inverter PWB	179
1-5-5 Developing section	181
(1) Detaching and refitting the developing unit	181
1-5-6 Drum section	182
(1) Detaching and refitting the drum unit	182
(2) Detaching and refitting the main charger unit	183
1-5-7 Transfer/separation section	184
(1) Detaching and refitting the transfer roller	184
1-5-8 Fuser section	186
(1) Detaching and refitting the fuser unit	186
(2) Switching the fuser pressure	190
1-5-9 PWBs	191
(1) Detaching and refitting the control PWB	191
(2) Detaching and refitting the power source PWB	194
(3) Detaching and refitting the high voltage PWB	197
(4) Detaching and refitting the scanner PWB	201
(5) Detaching and refitting the FAX PWB	202
1-5-10 Others	203
(1) Detaching and refitting the main motor	203
(2) Direction of installing the left cooling fan motor, right cooling fan motor and power source fan motor	204
1-5-11 DP	205
Requirements on PWB Replacement	207
1-6-1 Upgrading the firmware	207
1-6-2 Remarks on control PWB replacement	208
Mechanical Construction	209
2-1-1 Paper feed/conveying section	209
(1) Cassette paper feed section	209
(2) MP tray paper feed section	210
(3) Paper conveying section	211
2-1-2 Drum section	212
(1) Drum section	212
(2) Main charger unit	213
2-1-3 Optical section	214
(1) Scanner unit	214
(2) Image scanner unit (ISU)	215
(3) Laser scanner unit	217
2-1-4 Developing section	219
2-1-5 Transfer/separation section	220
2-1-6 Cleaning section	221
2-1-7 Fuser section	222
2-1-8 Paper exit section	224
2-1-9 Duplex/conveying section	226
2-1-10 DP section	227
Electrical Parts Layout	229
2-2-1 Electrical parts layout	229
(1) PWBs	229
(2) Switches and sensors	231
(3) Other electrical components	232
(4) DP	233
Operation of the PWBs	235
2-3-1 Power source PWB	235
2-3-2 Control PWB	237
2-3-3 Scanner PWB	243
2-3-4 DP driver PWB	246
Appendixes	247
2-4-1 Appendixes	247
(1) Wiring diagram	247
(2) Repetitive defects gauge	249

Match case Limit results 1 per page

2JN

1-4-26

(2-5) U010XX error code table: G3 transmission

Error code

Description

U01000

An FTT signal was received for a set number of times after TCF signal transmission at 2400 bps.

Or, an RTN signal was received in response to a Q signal (excluding EOP) after transmission at

2400 bps.

U01001

Function of the unit differs from that indicated by a DIS signal.

U01010

No relevant signal was received after transmission of a DNL (MPS or EOM) signal, and the preset

number of command retransfers was exceeded (between units of our make).

U01011

No relevant signal was received after transmission of a DCS, TCF signal, and the preset number

of command retransfers was exceeded.

U01012

No relevant signal was received after transmission of an NSS1, NSS2 (TCF) signal, and the preset

number of command retransfers was exceeded (between units of our make).

U01013

No relevant signal was received after transmission of an NSS3, TCF signal, and the preset number

of command retransfers was exceeded (between units of our make).

U01014

No relevant signal was received after transmission of an MPS signal, and the preset number of

command retransfers was exceeded.

U01015

No relevant signal was received after transmission of an EOM signal, and the preset number of

command retransfers was exceeded.

U01016

An MCF signal was received but no DIS signal was received after transmission of an EOM signal,

and T1 timeout was detected.

U01017

No relevant signal was received after transmission of an EOP signal, and the preset number of

command retransfers was exceeded.

U01018

No relevant signal was received after transmission of a PRI-EOP signal, and the preset number of

command retransfers was exceeded.

U01019

No relevant signal was received after transmission of a CNC signal, and the preset number of

command retransfers was exceeded (between units of our make).

U01020

No relevant signal was received after transmission of a CTC signal, and the preset number of com-

mand retransfers was exceeded (ECM).

U01021

No relevant signal was received after transmission of an EOR.Q signal, and the preset number of

command retransfers was exceeded (ECM).

U01022

No relevant signal was received after transmission of an RR signal, and the preset number of com-

mand retransfers was exceeded (ECM).

U01023

No relevant signal was received after transmission of a PSS.NULL signal, and the preset number

of command retransfers was exceeded (ECM).

U01024

No relevant signal was received after transmission of a PSS.MPS signal, and the preset number of

command retransfers was exceeded (ECM).

U01025

No relevant signal was received after transmission of a PPS.EOM signal, and the preset number of

command retransfers was exceeded (ECM).

U01026

No relevant signal was received after transmission of a PPS.EOP signal, and the preset number of

command retransfers was exceeded (ECM).

U01027

No relevant signal was received after transmission of a PPS.PRI-EOP signal, and the preset num-

ber of command retransfers was exceeded (ECM).

U01028

T5 time-out was detected during ECM transmission (ECM).

U01040

A DCN or other inappropriate signal was received during standby for DIS signal reception.

U01041

A DCN signal was received after transmission of a DNL (MPS or EOM) signal (between units of

our make).

U01042

A DCN signal was received after transmission of a DCS, TCF signal.