Home » Kyocera Manuals » Printers » Kyocera FS-1128MFP » Manual Viewer

Kyocera FS-1128MFP Service Manual - Page 83

Setting ECM reception, Sets ECM transmission. - cost per page

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

2JN Maintenance item No. Description U630 (cont.) Setting the waiting period to prevent echo problems at the receiver Sets the period before an NSF, CSI or DIS signal is sent after a CED signal is received. Used when problems occur due to echoes at the receiver. 1. Select the setting using the cursor up/down keys. Display Description 500 Sends an NSF, CSI or DIS 500 ms after receiving a CED. 75 Sends an NSF, CSI or DIS 75 ms after receiving a CED. U631 Initial setting: 75 2. Press the start key. The setting is set. Completion Press the stop key. The screen for selecting a maintenance item No. is displayed. Setting communication control 2 Description Makes settings regarding fax transmission. Start 1. Press the start key. 2. Select the item to be set using the cursor up/down keys. Display Description ECM TX Sets ECM transmission. ECM RX Sets ECM reception. CED FREQ. Sets the frequency of the CED signal. Setting ECM transmission To be set to OFF when reduction of transmission costs is of higher priority than image quality. This should not be set to OFF when connecting to the IP (Internet Protocol) telephone line. 1. Select the setting using the cursor up/down keys. Display Description ON ECM transmission is enabled. OFF ECM transmission is disabled. Initial setting: ON 2. Press the start key. The setting is set. Setting ECM reception To be set to OFF when reduction of transmission costs is of higher priority than image quality. This should not be set to OFF when connecting to the IP (Internet Protocol) telephone line. 1. Select the setting using the cursor up/down keys. Display Description ON ECM reception is enabled. OFF ECM reception is disabled. Initial setting: ON 2. Press the start key. The setting is set. Setting the frequency of the CED signal Sets the frequency of the CED signal. Used as one of the measures to improve transmission performance for international communications. 1. Select the setting using the cursor up/down keys. Display Description 2100 2100 Hz 1100 1100 Hz Initial setting: 2100 2. Press the start key. The setting is set. Completion Press the stop key. The screen for selecting a maintenance item No. is displayed. 1-3-55

Section	Page
Cover	1
Revision history	3
Safety precautions	5
CONTENTS	11
Specifications	15
1-1-1 Specifications	15
1-1-2 Parts names	18
(1) Overall	18
(2) Operation panel	19
1-1-3 Machine cross section	20
Installation	23
1-2-1 Installation environment	23
1-2-2 Unpacking	24
(1) Unpacking	24
(2) Removing the tapes	25
1-2-3 Installing the expansion memory (option)	28
Maintenance Mode	29
1-3-1 Maintenance mode	29
(1) Executing a maintenance item	29
(2) Maintenance modes item list	30
(3) Contents of the maintenance mode items	34
1-3-2 Management mode	103
(1) Using the management mode	103
(2) Common Settings	104
(3) Copy Settings	108
(4) Sending Settings	108
(5) Document Box Settings	108
(6) Printer Settings	109
(7) Printing Reports/Sending Notice	109
(8) Adjustment/Maintenance	110
(9) Date/Timer	110
(10) Editing Destination (Address Book/Adding One- Touch Keys)	111
(11) Restarting the System	112
(12) Network Setup	112
(13) User Login Administration	114
(14) Job accounting	114
(15) FAX Settings	116
Troubleshooting	119
1-4-1 Paper misfeed detection	119
(1) Paper misfeed indication	119
(2) Paper misfeed detection condition	120
1-4-2 Self-diagnostic function	121
(1) Self-diagnostic function	121
(2) Self diagnostic codes	122
1-4-3 Image formation problems	130
(1) Completely blank printout.	131
(2) All-black printout.	131
(3) Dropouts.	132
(4) Black dots.	132
(5) Black horizontal streaks.	132
(6) Black vertical streaks.	133
(7) Unsharpness.	133
(8) Gray background.	133
(9) Dirt on the top edge or back of the paper.	134
(10) Undulated printing at the right edge (scanning start position).	134
1-4-4 Electric problems	135
1-4-5 Mechanical problems	138
1-4-6 Error codes	139
(1) Error code	139
(2) Table of general classification	140
(2-1) U004XX error code table: Interrupted phase B	142
(2-2) U006XX error code table: Problems with the unit	143
(2-3) U008XX error code table: Page transmission error	143
(2-4) U009XX error code table: Page reception error	143
(2-5) U010XX error code table: G3 transmission	144
(2-6) U011XX error code table: G3 reception	146
(2-7) U017XX error code table: V.34 transmission	148
(2-8) U018XX error code table: V.34 reception	148
(2-9) U023XX error code table: Relay command abnormal reception	148
(2-10) U044XX error code table: Encrypted transmission	148
1-4-7 Send error code	149
(1) Scan to SMB error codes	149
(2) Scan to FTP error codes	150
(3) Scan to E-mail error codes	151
(4) Network Twain error codes	152
(5) Software trouble error codes	152
Assembly and Disassembly	153
1-5-1 Precautions for assembly and disassembly	153
(1) Precautions	153
(2) Drum	153
(3) Toner	153
(4) How to tell a genuine Kyocera Mita toner container	154
1-5-2 Outer covers	155
(1) Detaching and refitting the left cover and right cover	155
1-5-3 Paper feed section	158
(1) Detaching and refitting the paper feed assembly (paper feed roller and pickup roller)	158
(2) Detaching and refitting the retard roller assembly	160
(3) Detaching and refitting the MP paper feed roller	162
(4) Note on removing and Installing the upper registration roller and lower registration roller	164
1-5-4 Optical section	165
(1) Detaching and refitting the DP	165
(2) Detaching and refitting the scanner unit	166
(3) Detaching and refitting the laser scanner unit (LSU)	169
(4) Replacing the image scanner unit (ISU)	173
(5) Detaching and refitting the exposure lamp and inverter PWB	179
1-5-5 Developing section	181
(1) Detaching and refitting the developing unit	181
1-5-6 Drum section	182
(1) Detaching and refitting the drum unit	182
(2) Detaching and refitting the main charger unit	183
1-5-7 Transfer/separation section	184
(1) Detaching and refitting the transfer roller	184
1-5-8 Fuser section	186
(1) Detaching and refitting the fuser unit	186
(2) Switching the fuser pressure	190
1-5-9 PWBs	191
(1) Detaching and refitting the control PWB	191
(2) Detaching and refitting the power source PWB	194
(3) Detaching and refitting the high voltage PWB	197
(4) Detaching and refitting the scanner PWB	201
(5) Detaching and refitting the FAX PWB	202
1-5-10 Others	203
(1) Detaching and refitting the main motor	203
(2) Direction of installing the left cooling fan motor, right cooling fan motor and power source fan motor	204
1-5-11 DP	205
Requirements on PWB Replacement	207
1-6-1 Upgrading the firmware	207
1-6-2 Remarks on control PWB replacement	208
Mechanical Construction	209
2-1-1 Paper feed/conveying section	209
(1) Cassette paper feed section	209
(2) MP tray paper feed section	210
(3) Paper conveying section	211
2-1-2 Drum section	212
(1) Drum section	212
(2) Main charger unit	213
2-1-3 Optical section	214
(1) Scanner unit	214
(2) Image scanner unit (ISU)	215
(3) Laser scanner unit	217
2-1-4 Developing section	219
2-1-5 Transfer/separation section	220
2-1-6 Cleaning section	221
2-1-7 Fuser section	222
2-1-8 Paper exit section	224
2-1-9 Duplex/conveying section	226
2-1-10 DP section	227
Electrical Parts Layout	229
2-2-1 Electrical parts layout	229
(1) PWBs	229
(2) Switches and sensors	231
(3) Other electrical components	232
(4) DP	233
Operation of the PWBs	235
2-3-1 Power source PWB	235
2-3-2 Control PWB	237
2-3-3 Scanner PWB	243
2-3-4 DP driver PWB	246
Appendixes	247
2-4-1 Appendixes	247
(1) Wiring diagram	247
(2) Repetitive defects gauge	249

Match case Limit results 1 per page

2JN

1-3-55

U630

(cont.)

Setting the waiting period to prevent echo problems at the receiver

Sets the period before an NSF, CSI or DIS signal is sent after a CED signal is received. Used when problems

occur due to echoes at the receiver.

Select the setting using the cursor up/down keys.

Initial setting: 75

Press the start key. The setting is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U631

Setting communication control 2

Description

Makes settings regarding fax transmission.

Start

Press the start key.

Select the item to be set using the cursor up/down keys.

Setting ECM transmission

To be set to OFF when reduction of transmission costs is of higher priority than image quality.

This should not be set to OFF when connecting to the IP (Internet Protocol) telephone line.

Select the setting using the cursor up/down keys.

Initial setting: ON

Press the start key. The setting is set.

Setting ECM reception

To be set to OFF when reduction of transmission costs is of higher priority than image quality.

This should not be set to OFF when connecting to the IP (Internet Protocol) telephone line.

Select the setting using the cursor up/down keys.

Initial setting: ON

Press the start key. The setting is set.

Setting the frequency of the CED signal

Sets the frequency of the CED signal. Used as one of the measures to improve transmission performance for

international communications.

Select the setting using the cursor up/down keys.

Initial setting: 2100

Press the start key. The setting is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

500

Sends an NSF, CSI or DIS 500 ms after receiving a CED.

Sends an NSF, CSI or DIS 75 ms after receiving a CED.

Display

Description

ECM TX

Sets ECM transmission.

ECM RX

Sets ECM reception.

CED FREQ.

Sets the frequency of the CED signal.

Display

Description

ECM transmission is enabled.

OFF

ECM transmission is disabled.

Display

Description

ECM reception is enabled.

OFF

ECM reception is disabled.

Display

Description

2100

2100 Hz

1100

1100 Hz