Singer SE300 Legacy Instruction Manual and Troubleshooting Guide - Page 19

Threading The Needle

Get Singer SE300 Legacy PDF manuals and user guides View all Singer SE300 Legacy manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

SETTING UP THE MACHINE THREADING THE MACHINE THREADING THE NEEDLE PREPARING TO THREAD MACHINE 5$,6(7+(35(66(5)227/,)7(5,WLVYHU\LPSRUWDQW to raise the presser foot lifter before you proceed to thread the machine. 2. Raise the needle in highest position by turning the handwheel toward you.  .HHSWKLVSRVLWLRQIRUWKUHDGLQJWKHH\HRIWKHQHHGOH NOTE: It is very important to raise the presser foot lifter before you thread the machine. Not doing so will likely result in poor VWLWFKTXDOLW\RUH[FHVVLYHWKUHDGORRSVRQWKHXQGHUVLGHRI the fabric. Always raise the presser foot lifter before you begin threading the machine. THREADING THE UPPER THREAD 1. Hold thread in both hands and pass thread into the guide from front opening. 2. Bring thread backward and pass through the slit from right to left. 3. Bring thread to the left and pull thread down toward you along the slit. 4. Pull the thread around the U-turn, then bring it back up. 5. To thread the take-up lever, draw thread up and bring thread back down again from right to left along the slit. 6. Pull thread downward along the slit. 7. Draw thread through thread guide from right side opening. 8. Pass through needle eye from front to back. Refer to next page for instructions on how to use needle threader. SETTING SPOOL OF THREAD ON SPOOL PIN 1. Pull up the left end of spool pin and set the felt washer and the spool of thread on spool pin so that the thread unrolls from the front of the spool. 2. 6HWWKHVSRROFDSRQVSRROSLQDVIDUDVLWZLOOJR a. Reverse spool cap direction according to the size of spool. b. Use the small spool cap when you use cross wound thread. Leave small opening between cap and spool as illustrated. c. 6HWWKHWKUHDGQHWRYHUWKHVSRROLIWKUHDGXQUROOVWRR easily. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
19
SETTING UP THE MACHINE
THREADING THE NEEDLE
P
REPARING
TO
T
HREAD
M
ACHINE
ܵ 5$¸6( 7+( 35(66(5 )227 /¸)7(5µ ¸W LV YH³\ LPSR³W´QW
to raise the presser foot lifter before you proceed to thread
the machine.
2.
Raise the needle in highest position by turning the
handwheel toward you.
»²HHS W¶LV SRVLWLRQ IR³ W¶³H´GLQJ W¶H H\H RI W¶H QHHGOHµÁ
NOTE:
It is very important to raise the presser foot lifter before you
thread the machine.
Not doing so will likely result in poor
VWLWF¶ TX´OLW\ R³ H[FHVVLYH W¶³H´G ORRSV RQ W¶H XQGH³VLGH RI
the fabric. Always raise the presser foot lifter before you begin
threading the machine.
T
HREADING
THE
M
ACHINE
S
ETTING
S
POOL
OF
T
HREAD
ON
S
POOL
P
IN
1.
Pull up the left end of spool pin and set the felt washer and
the spool of thread on spool pin so that the thread unrolls
from the front of the spool.
2.
6HW W¶H VSRRO F´S RQ VSRRO SLQ ´V I´³ ´V LW ZLOO JRµ
a. Reverse spool cap direction according to the size of
spool.
b. Use the small spool cap when you use cross wound
thread. Leave small opening between cap and spool as
illustrated.
c.
6HW W¶H W¶³H´G QHW RYH³ W¶H VSRRO LI W¶³H´G XQ³ROOV WRR
easily.
T
HREADING
THE
U
PPER
T
HREAD
1.
Hold thread in both hands and pass thread into the guide
from front opening.
2.
Bring thread backward and pass through the slit from right
to left.
3.
Bring thread to the left and pull thread down toward you
along the slit.
4.
Pull the thread around the U-turn, then bring it back up.
5.
To thread the take-up lever, draw thread up and bring
thread back down again from right to left along the slit.
6.
Pull thread downward along the slit.
Ô.
Draw thread through thread guide from right side opening.
8.
Pass through needle eye from front to back.
Refer to next page for instructions on how to use needle
threader.