Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 107

The Integrated Management Log, Single Bit Errors

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

3-10 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide Table 3-2 POST Error Messages continued Error Code Audible Beeps 163-Time & Date Not Set 2 short 164-Memory Size Error 2 short 172-Configuration None Nonvolatile Memory Invalid 173-Slot ID None Mismatch 174-Configuration/ None Slot Mismatch Device Not Found 175-Configuration/ None Slot Mismatch Device Found 177-Configuration None Not Complete 178-Processor None Configuration Invalid 180-Log Reinitialized None 201-Memory Error None 202-Memory Type Mismatch 2 short 203-Memory None Address Error 207-ECC Corrected None Single Bit Errors in DIMM in Memory Module Socket 207-Invalid Memory None Configuration - Check DIMM Installation Probable Source of Problem Invalid time or date in configuration memory. Configuration memory Incorrect. Nonvolatile configuration corrupted. Recommended Action Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Board replaced, configuration not updated. EISA or PCI board not found. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. EISA or PCI board added, configuration not updated. Run the System Configuration Utility and correct. Incomplete system configuration detected. Processor type or step does not match configuration memory. The Integrated Management Log has been reinitialized, probably due to corruption of the log. RAM failure detected. An incompatible memory module is installed in the system. RAM failure. Memory module is malfunctioning. Memory module installed incorrectly. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Event message, none needed. Run Compaq Diagnostics. Replace failed assembly as indicated. Compare Compaq part numbers from installed memory modules with the manual. If not listed, the memory modules are incompatible and should be replaced or removed. Run Compaq Diagnostics. Replace failed assembly as indicated. Run Compaq Diagnostics. Replace or remove malfunctioning memory module as indicated. Verify placement of memory modules. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
3-10
Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
163-Time & Date Not
Set
2 short
Invalid time or date in
configuration memory.
Run the System Configuration
Utility and correct.
164-Memory Size
Error
2 short
Configuration memory Incorrect.
Run the System Configuration
Utility and correct.
172-Configuration
Nonvolatile Memory
Invalid
None
Nonvolatile configuration
corrupted.
Run the System Configuration
Utility and correct.
173-Slot ID
Mismatch
None
Board replaced, configuration not
updated.
Run the System Configuration
Utility and correct.
174-Configuration/
Slot Mismatch Device
Not Found
None
EISA or PCI board not found.
Run the System Configuration
Utility and correct.
175-Configuration/
Slot Mismatch Device
Found
None
EISA or PCI board added,
configuration not updated.
Run the System Configuration
Utility and correct.
177-Configuration
Not Complete
None
Incomplete system configuration
detected.
Run the System Configuration
Utility and correct.
178-Processor
Configuration Invalid
None
Processor type or step does not
match configuration memory.
Run the System Configuration
Utility and correct.
180-Log Reinitialized
None
The Integrated Management Log
has been reinitialized, probably
due to corruption of the log.
Event message, none needed.
201-Memory Error
None
RAM failure detected.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
202-Memory Type
Mismatch
2 short
An incompatible memory module
is installed in the system.
Compare Compaq part numbers
from installed memory modules
with the manual.
If not listed, the memory
modules are incompatible and
should be replaced or removed.
203-Memory
Address Error
None
RAM failure.
Run Compaq Diagnostics.
Replace failed assembly as
indicated.
207-ECC Corrected
Single Bit Errors in
DIMM in Memory
Module Socket
None
Memory module is
malfunctioning.
Run Compaq Diagnostics.
Replace or remove
malfunctioning memory module
as indicated.
207-Invalid Memory
Configuration –
Check DIMM
Installation
None
Memory module installed
incorrectly.
Verify placement of memory
modules.
continued