Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 87

Extended SCSI Dividers, Array Controllers with Extended

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

2-70 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide Extended SCSI Dividers Extended SCSI dividers, adjacent to slots 10 and 11, provide leverage for removing and replacing extended SCSI array controllers and add insulation to any PCI board plugged into these slots. To remove an Extended SCSI divider: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the top access panel. See "Top Access Panel" earlier in this chapter. 3. Remove the array controllers with Extended SCSI. See "Array Controllers with Extended SCSI" earlier in this chapter. 4. Pull up the single push-pull fastener . 5. Push in the locking lever on the expansion board guide and lift the Extended SCSI divider out of the unit . 2 3 1 Figure 2-61. Removing an Extended SCSI divider Reverse steps 1 through 5 to replace an Extended SCSI divider.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
2-70
Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Extended SCSI Dividers
Extended SCSI dividers, adjacent to slots 10 and 11, provide leverage for removing and
replacing extended SCSI array controllers and add insulation to any PCI board plugged into
these slots.
To remove an Extended SCSI divider:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the top access panel. See
“
Top Access Panel
”
earlier in this chapter.
3.
Remove the array controllers with Extended SCSI. See
“
Array Controllers with Extended
SCSI
”
earlier in this chapter.
4.
Pull up the single push-pull fastener
.
5.
Push in the locking lever on the expansion board guide
and lift the Extended SCSI
divider out of the unit
.
2
3
1
Figure 2-61.
Removing an Extended SCSI divider
Reverse steps 1 through 5 to replace an Extended SCSI divider.