Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 155

SOLUTION: This, power down

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 155 highlights

3-58 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide Table 3-16 ADU Diagnostic Messages continued Message Description Storage enclosure on SCSI bus X - Wide SCSI transfer failed. A cable on bus X has failed. SOLUTION: This may indicate a bad SCSI cable on bus X. Try replacing the cable. Swapped cables or Configuration error detected. A configured array of drives was moved from another controller that supported more drives than this controller supports. You have exceeded the maximum number of drives supported for this controller and the attached controller was not part of the original array configuration. SOLUTION: Upgrade the firmware on this controller. If this doesn't solve the problem, then power down system and move the drives back to the original controller. Recommended Action 1. Replace the failed cable. 2. If that does not solve the problem, contact your Compaq authorized service provider. 1. Upgrade the firmware on this controller. 2. If the problem is not resolved: Replace this controller with the original controller. -OrReplace this controller with a new controller that supports the number of drives in the array. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
3-58
Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-16
ADU Diagnostic Messages
continued
Message
Description
Recommended Action
Storage
enclosure on
SCSI bus X
–
Wide SCSI
transfer failed.
SOLUTION: This
may indicate a
bad SCSI cable
on bus X. Try
replacing the
cable.
A cable on bus X has failed.
1.
Replace the failed cable.
2.
If that does not solve the problem, contact
your Compaq authorized service provider.
Swapped cables
or Configuration
error detected.
A configured
array of drives
was moved from
another
controller that
supported more
drives than this
controller
supports.
SOLUTION:
Upgrade the
firmware on this
controller. If this
doesn
’
t solve the
problem, then
power down
system and
move the drives
back to the
original
controller.
You have exceeded the maximum
number of drives supported for this
controller and the attached controller
was not part of the original array
configuration.
1.
Upgrade the firmware on this controller.
2.
If the problem is not resolved:
Replace this controller with the original
controller.
-Or-
Replace this controller with a new
controller that supports the number of
drives in the array.
continued