Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 118

Detected. If more, failed Set Block

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Diagnostics and Troubleshooting 3-21 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1727-Slot x Drive None Array - New Logical Drive(s) Attachment Detected. If more than 32 logical drives, this message will be followed by: Auto-configuration failed: Too many logical drives. 1729-Slot 1 Drive None Array - Disk Consistency Initialization in Progress - RAID 4/5 performance may be lower until Auto Reliability Monitoring has completed Automatic Background Parity Consistency Initialization. 1730-Fixed Disk 0 None does not support DMA Mode. 1731-Fixed Disk 1 None does not support DMA Mode. 1740-Fixed Disk 0 None failed Set Block Mode command 1741-Fixed Disk 1 None failed Set Block Mode command 1750-Fixed Disk 0 None failed Identify command Probable Source of Problem Additional drives detected. Initial RAID configuration in progress. Fixed disk drive error detected. Fixed disk drive error detected. Fixed disk drive error detected. Fixed disk drive error detected. Fixed disk drive error detected. Recommended Action This message indicates that the controller has detected an additional array of drives that was attached when the power was off. The logical drive configuration information has been updated to add the new logical drives. The maximum number of logical drives supported is 32. Additional logical drives will not be added to the configuration. Press F1 key to resume. This message is normal following the initial configuration of RAID 4 or RAID 5 logical drives. Performance of the controller will improve after the parity data has been initialized by ARM (an automatic process that runs in the background on the controller). Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Diagnostics and Troubleshooting
3-21
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1727-Slot x Drive
Array
–
New Logical
Drive(s) Attachment
Detected. If more
than 32 logical
drives, this message
will be followed by:
Auto-configuration
failed: Too many
logical drives.
None
Additional drives detected.
This message indicates that the
controller has detected an
additional array of drives that
was attached when the power
was off. The logical drive
configuration information has
been updated to add the new
logical drives. The maximum
number of logical drives
supported is 32. Additional
logical drives will not be added
to the configuration. Press
F1
key to resume.
1729-Slot 1 Drive
Array
–
Disk
Consistency
Initialization in
Progress
–
RAID 4/5
performance may be
lower until Auto
Reliability Monitoring
has completed
Automatic
Background Parity
Consistency
Initialization.
None
Initial RAID configuration in
progress.
This message is normal
following the initial
configuration of RAID 4 or
RAID 5 logical drives.
Performance of the controller
will improve after the parity data
has been initialized by ARM (an
automatic process that runs in
the background on the
controller).
1730-Fixed Disk 0
does not support
DMA Mode.
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
1731-Fixed Disk 1
does not support
DMA Mode.
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
1740-Fixed Disk 0
failed Set Block
Mode command
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
1741-Fixed Disk 1
failed Set Block
Mode command
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
1750-Fixed Disk 0
failed Identify
command
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
continued