Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 71

Processor Terminator Boards

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

2-54 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide Processor Terminator Boards Processor terminator boards occupy unused processor sockets on the processor board. To remove a processor terminator board: 1. Perform the preparation procedures. See "Preparation Procedures" earlier in this chapter. 2. Remove the right side access panel. See "Right Side Access Panel" earlier in this chapter. 3. Remove the main processor air baffle. See "Main Processor Air Baffle" earlier in this chapter. 4. Rotate the side ejector levers on the processor terminator board outward approximately 120 degrees , then slide the processor terminator board out the right side of the server . 1 2 1 Figure 2-46. Removing a processor terminator board Reverse steps 1 through 4 to replace a processor terminator board. IMPORTANT: If the processor terminator board is not properly seated, the system interlock prevents the system from powering up.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
2-54
Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Processor Terminator Boards
Processor terminator boards occupy unused processor sockets on the processor board.
To remove a processor terminator board:
1.
Perform the preparation procedures. See
“
Preparation Procedures
”
earlier in this chapter.
2.
Remove the right side access panel. See
“
Right Side Access Panel
”
earlier in this chapter.
3.
Remove the main processor air baffle. See
“
Main Processor Air Baffle
”
earlier in
this chapter.
4.
Rotate the side ejector levers on the processor terminator board outward approximately
120 degrees
, then slide the processor terminator board out the right side of the server
.
1
2
1
Figure 2-46.
Removing a processor terminator board
Reverse steps 1 through 4 to replace a processor terminator board.
IMPORTANT:
If the processor terminator board is not properly seated, the system interlock prevents the
system from powering up.