Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 127

Run Compaq Diagnostics and, Controller or Disk

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

3-30 Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide Table 3-2 POST Error Messages continued Error Code Audible Beeps 1789-Slot X Drive None Array SCSI Drive(s) Not Responding. Check cables or replace the following SCSI drives: SCSI Port Y: SCSI ID Z Select F1 to continue - drive array will remain disabled. Select F2 to failed drives that are not responding - Interim Recovery Mode will be enabled if configured for fault tolerance. 1790-Disk 0 None Configuration Error 1791-Disk 1 Error None 1792-Drive Array None Reports Valid Data Found in Array Accelerator. Data will automatically be written to drive array. 1792-Secondary None Disk Controller Failure 1793-Secondary None Controller or Disk Failure 1793-Drive Array - None Array Accelerator Battery Depleted - Data Lost (Error message 1794 also displays.) Probable Source of Problem Cable or hard drive failure occurred. Recommended Action 1. Check the cable connections. 2. If cables are connected, replace the drive. 3. If you do not want to replace the drives at this time, press F2. Hard drive error or wrong drive type detected. Hard drive error or wrong drive type detected. This indicates that while the system was in use, power was interrupted while data was in the array accelerator memory. Power was then restored within 8 to 10 days, and the data in the array accelerator was flushed to the drive array. Part of the IDE drive electronics has failed. The IDE controller or an attached drive has failed. This indicates that while the system was in use, power was interrupted while data was in the array accelerator memory. Array accelerator batteries failed. Data in array accelerator has been lost. Run the System Configuration Utility and Diagnostics and Compaq Diagnostics and correct. Replace failed assembly as indicated. Run the System Configuration Utility and Diagnostics and Compaq Diagnostics and correct. Replace failed assembly as indicated. No action necessary; no data has been lost. Perform orderly system shutdowns to avoid data remaining in the array accelerator. Run Compaq Diagnostics and replace failed assembly as indicated. Run Compaq Diagnostics and replace failed assembly as indicated. Power was not restored within 8 to 10 days. Perform orderly system shutdowns to avoid data remaining in the array accelerator. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
3-30
Compaq ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maintenance and Service Guide
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1789-Slot
X
Drive
Array SCSI Drive(s)
Not Responding.
Check cables or
replace the following
SCSI drives:
SCSI Port
Y
:
SCSI ID
Z
Select F1 to continue
–
drive array will
remain disabled.
Select F2 to failed
drives that are not
responding
–
Interim
Recovery Mode will
be enabled if
configured for fault
tolerance.
None
Cable or hard drive failure
occurred.
1.
Check the cable
connections.
2.
If cables are connected,
replace the drive.
3.
If you do not want to
replace the drives at this
time, press
F2
.
1790-Disk 0
Configuration Error
None
Hard drive error or wrong drive
type detected.
Run the System Configuration
Utility and Diagnostics and
Compaq Diagnostics and
correct. Replace failed
assembly as indicated.
1791-Disk 1 Error
None
Hard drive error or wrong drive
type detected.
Run the System Configuration
Utility and Diagnostics and
Compaq Diagnostics and
correct. Replace failed
assembly as indicated.
1792-Drive Array
Reports Valid Data
Found in Array
Accelerator.
Data will
automatically be
written to drive array.
None
This indicates that while the
system was in use, power was
interrupted while data was in the
array accelerator memory. Power
was then restored within 8 to 10
days, and the data in the array
accelerator was flushed to the
drive array.
No action necessary; no data
has been lost. Perform orderly
system shutdowns to avoid data
remaining in the array
accelerator.
1792-Secondary
Disk Controller
Failure
None
Part of the IDE drive electronics
has failed.
Run Compaq Diagnostics and
replace failed assembly as
indicated.
1793-Secondary
Controller or Disk
Failure
None
The IDE controller or an attached
drive has failed.
Run Compaq Diagnostics and
replace failed assembly as
indicated.
1793-Drive Array -
Array Accelerator
Battery Depleted -
Data Lost
(Error message 1794
also displays.)
None
This indicates that while the
system was in use, power was
interrupted while data was in the
array accelerator memory.
Array accelerator batteries failed.
Data in array accelerator has
been lost.
Power was not restored within 8
to 10 days. Perform orderly
system shutdowns to avoid data
remaining in the array
accelerator.
continued