Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 66

CAUTION, IMPORTANT, to lock the processor in place.

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Removal and Replacement Procedures 2-49 To install a processor: CAUTION: When installing processors, be sure to install the Processor Power Module first to ensure proper processor operation. 1. Gently guide the processor into the processor slot. IMPORTANT: If the processor is not properly seated, the system interlock prevents the system from powering up. 2. Fully seat the processor . NOTE: The processor is keyed to ensure correct alignment. CAUTION: Do not lock the ejector levers before fully seating the processor into the slot. IMPORTANT: When installing a processor, push down on both levers simultaneously. The server may not recognize the processor if it is not properly installed. 3. Push both side ejector levers on the processor inward to lock the processor in place. 2 1 2 Figure 2-42. Installing a processor 4. Replace the main air baffle and access covers. 5. Restart the server. IMPORTANT: Verify that the processor board bus/core switch settings are correct. See Chapter 4, "Connectors, Switches, and Status Indicators," for the correct bus/core switch settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Removal and Replacement Procedures
2-49
To install a processor:
CAUTION:
When installing processors, be sure to install the Processor Power Module first to
ensure proper processor operation.
1.
Gently guide the processor into the processor slot.
IMPORTANT:
If the processor is not properly seated, the system interlock prevents the system from
powering up.
2.
Fully seat the processor
.
NOTE:
The processor is keyed to ensure correct alignment.
CAUTION:
Do not lock the ejector levers before fully seating the processor into the slot.
IMPORTANT:
When installing a processor, push down on both levers simultaneously. The server may
not recognize the processor if it is not properly installed.
3.
Push both side ejector levers on the processor inward
to lock the processor in place.
2
2
1
Figure 2-42.
Installing a processor
4.
Replace the main air baffle and access covers.
5.
Restart the server.
IMPORTANT:
Verify that the processor board bus/core switch settings are correct. See Chapter 4,
“
Connectors, Switches, and Status Indicators,
”
for the correct bus/core switch settings.