Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 124

Run Array Diagnostic Utility if, Run the Compaq Array

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Diagnostics and Troubleshooting 3-27 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1785-Slot X Drive None Array not Configured (followed by one of the following): (1) Run Compaq Array Configuration Utility (2) No drives detected (3) Drive positions appear to have changed - Run Drive Array Advanced Diagnostics if previous positions are unknown. Then turn system power OFF and move drives to their original positions. (4) Configuration information indicates drive positions beyond the capability of this controller. This may be due to drive movement from a controller that supports more drives than the current controller. (5) Configuration information indicates drives were configured on a controller with a newer firmware version. (RESUME = F1 KEY) Probable Source of Problem Drive array configuration not detected. Recommended Action (1) Run the Compaq Array Configuration Utility. (2) Turn off system and check SCSI cable connections to make sure drives are attached properly. (3) Run Array Diagnostic Utility if previous positions are unknown. Then turn system power off and move drives to their original positions. (4) To avoid data loss, turn system power off and reattach drives to the original controller. (5) To avoid data loss, reattach drives to the original controller or upgrade the controller firmware to the version on the original controller using Option ROMPaq. Press F1 to resume. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Diagnostics and Troubleshooting
3-27
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1785-Slot X Drive
Array not Configured
(followed by one of
the following):
(1) Run Compaq
Array Configuration
Utility
(2) No drives
detected
(3) Drive positions
appear to have
changed
–
Run Drive
Array Advanced
Diagnostics if
previous positions
are unknown. Then
turn system power
OFF and move drives
to their original
positions.
(4) Configuration
information indicates
drive positions
beyond the capability
of this controller.
This may be due to
drive movement from
a controller that
supports more drives
than the current
controller.
(5) Configuration
information indicates
drives were
configured on a
controller with a
newer firmware
version.
(RESUME = F1 KEY)
None
Drive array configuration not
detected.
(1) Run the Compaq Array
Configuration Utility.
(2) Turn off system and check
SCSI cable connections to make
sure drives are attached
properly.
(3) Run Array Diagnostic Utility if
previous positions are unknown.
Then turn system power off and
move drives to their original
positions.
(4) To avoid data loss, turn
system power off and reattach
drives to the original controller.
(5) To avoid data loss, reattach
drives to the original controller
or upgrade the controller
firmware to the version on the
original controller using Option
ROMPaq.
Press
F1
to resume.
continued