Compaq ProLiant 8000 ProLiant 8000 Intel Pentium III Xeon 700MHz Servers Maint - Page 120

Compaq Options ROMPaq utility, Disk Port Address

Get Compaq ProLiant 8000 PDF manuals and user guides View all Compaq ProLiant 8000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 120 highlights

Diagnostics and Troubleshooting 3-23 Table 3-2 POST Error Messages continued Error Code Audible Beeps 1768-Slot x Drive None Array-Resuming logical drive expansion process. 1769-Slot x Drive None Array - Drive(s) disabled due to failure during expand. Select F1 to continue with logical drives disabled. Select F2 to accept data loss and to re- enable logical drives. 1770-Slot X Drive None Array - Critical Drive Firmware Problem Detected - Please upgrade firmware on the following drive(s) using Options ROMPaq (available from www.compaq.com): SCSI Port Y SCSI ID Z (RESUME = F1 OR F2 KEY) 1771-Primary Disk None Port Address Assignment Conflict 1772-Secondary None Disk Port Address Assignment Conflict 1773-Primary Fixed None Disk Port Assignment Conflict 1774-Slot X Drive None Array - Obsolete data found in Array Accelerator. Select F1 to discard contents of Array Accelerator. Select F2 to write contents of Array Accelerator to drives. Probable Source of Problem SMART-2 Controller error detected. SMART-2 Controller error detected. Recommended Action No action required. Appears whenever a controller reset or power cycle occurs while array expansion is in progress. Data has been lost while expanding the array; therefore, the drives have been temporarily disabled. Press F2 to accept the data loss and reenable the logical drives. Restore data from backup. Firmware update need indicated. The indicated drives are running firmware that is known to cause intermittent problems. Use the Compaq Options ROMPaq utility to upgrade firmware on all drives to the latest revision. Acquire from the Compaq website: http://www.compaq.com/ support Internal and external hard drive controllers are both assigned to the primary address. Address Assignment Conflict. Internal and external hard drive controllers are both assigned to the secondary address. Fixed disk drive error detected. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. Run the System Configuration Utility and correct. SMART-2 Controller error detected. Data found in array accelerator is older than data found on drives. Press F1 to discard the older data in the array accelerator and retain the newer data on the drives. continued

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Diagnostics and Troubleshooting
3-23
Table 3-2
POST Error Messages
continued
Error Code
Audible Beeps
Probable Source of Problem
Recommended Action
1768-Slot x Drive
Array-Resuming
logical drive
expansion process.
None
SMART-2 Controller error
detected.
No action required. Appears
whenever a controller reset or
power cycle occurs while array
expansion is in progress.
1769-Slot x Drive
Array - Drive(s)
disabled due to
failure during
expand. Select
F1
to
continue with logical
drives disabled.
Select
F2
to accept
data loss and to re-
enable logical drives.
None
SMART-2 Controller error
detected.
Data has been lost while
expanding the array; therefore,
the drives have been
temporarily disabled. Press
F2
to accept the data loss and
reenable the logical drives.
Restore data from backup.
1770-Slot
X
Drive
Array
–
Critical Drive
Firmware Problem
Detected
–
Please
upgrade firmware on
the following drive(s)
using Options
ROMPaq (available
from
www.compaq.com):
SCSI Port
Y
SCSI ID
Z
(RESUME = F1 OR
F2 KEY)
None
Firmware update need indicated.
The indicated drives are running
firmware that is known to cause
intermittent problems. Use the
Compaq Options ROMPaq utility
to upgrade firmware on all
drives to the latest revision.
Acquire from the Compaq
website:
support
1771-Primary Disk
Port Address
Assignment Conflict
None
Internal and external hard drive
controllers are both assigned to
the primary address.
Run the System Configuration
Utility and correct.
1772-Secondary
Disk Port Address
Assignment Conflict
None
Address Assignment Conflict.
Internal and external hard drive
controllers are both assigned to
the secondary address.
Run the System Configuration
Utility and correct.
1773-Primary Fixed
Disk Port Assignment
Conflict
None
Fixed disk drive error detected.
Run the System Configuration
Utility and correct.
1774-Slot X Drive
Array - Obsolete data
found in Array
Accelerator.
Select
F1
to discard
contents of Array
Accelerator.
Select
F2
to write
contents of Array
Accelerator to drives.
None
SMART-2 Controller error
detected.
Data found in array accelerator
is older than data found on
drives. Press
F1
to discard the
older data in the array
accelerator and retain the
newer data on the drives.
continued