Dell Brocade 825 Brocade Adapters Troubleshooting Guide - Page 91

Adapter event messages

Get Dell Brocade 825 PDF manuals and user guides View all Dell Brocade 825 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Adapter event messages 3 • portLogShowPort Use this command to display the port log for a specified switch port. • portPerfShow Use this command to display throughput information for all ports on the switch. • portStatsShow Use this command to display hardware statistics counters for a specific switch port. • portShow Use this command to display information and status of a specified switch port, including the speed, ID, operating state, type, and WWN. • SecAuthSecret Use this command to manage the DH-CHAP shared secret key database used for authentication. This command displays, sets, and removes shared secret key information from the databases. • sfpShow Use this command to display detailed information about specific SFPs installed in a switch. This command is supported on stand-up adapters only. • show vlan brief Displays information about a VLAN interface on the switch. • show dcb maps Displays information about the configured DCB maps in the switch. • switchShow Use this command to display switch and port information. Output may vary depending on the switch model. Use this information to determine the fabric port WWN and PID connected to an adapter port. Also display topology, speed, and state of each port on the switch. • trunkshow Use this command to display trunking information for the switch, such as the configuration, bandwidth, and throughput of trunk groups. Adapter event messages When applicable events occur during adapter operation, the adapter driver generates event messages. These messages are captured in your host system logs. These messages are also captured in an agtEvent.log file by the HCM and displayed in the HCM master log. Note that message display may differ in your host system log and the HCM master log, however messages may contain the following information: • Message ID • Description • Severity level • Event category • Cause of event • Recommended action Brocade Adapters Troubleshooting Guide 67 53-1002145-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Brocade Adapters Troubleshooting Guide
67
53-1002145-01
Adapter event messages
3
•
portLogShowPort
Use this command to display the port log for a specified switch port.
•
portPerfShow
Use this command to display throughput information for all ports on the switch.
•
portStatsShow
Use this command to display hardware statistics counters for a specific switch port.
•
portShow
Use this command to display information and status of a specified switch port, including the
speed, ID, operating state, type, and WWN.
•
SecAuthSecret
Use this command to manage the DH-CHAP shared secret key database used for
authentication. This command displays, sets, and removes shared secret key information from
the databases.
•
sfpShow
Use this command to display detailed information about specific SFPs installed in a switch.
This command is supported on stand-up adapters only.
•
show vlan brief
Displays information about a VLAN interface on the switch.
•
show dcb maps
Displays information about the configured DCB maps in the switch.
•
switchShow
Use this command to display switch and port information. Output may vary depending on the
switch model. Use this information to determine the fabric port WWN and PID connected to an
adapter port. Also display topology, speed, and state of each port on the switch.
•
trunkshow
Use this command to display trunking information for the switch, such as the configuration,
bandwidth, and throughput of trunk groups.
Adapter event messages
When applicable events occur during adapter operation, the adapter driver generates event
messages. These messages are captured in your host system logs. These messages are also
captured in an agtEvent.log file by the HCM and displayed in the HCM master log. Note that
message display may differ in your host system log and the HCM master log, however messages
may contain the following information:
•
Message ID
•
Description
•
Severity level
•
Event category
•
Cause of event
•
Recommended action