Dell MX9116n EMC SmartFabric OS10 User Guide - Page 69

• -B - (Optional) Does not allow ping to change the source address of probes. The source address is bound to the address used when the ping starts. • -c count - (Optional) Stops the ping after sending the specified number of ECHO_REQUEST packets until the timeout expires. • -d - (Optional) Sets the SO_DEBUG option on the socket being used. • -D - (Optional) Prints the timestamp before each line. • -F flowlabel - (Optional) Sets a 20-bit flow label on echo request packets. If value is zero, the kernel allocates a random flow label. • -h - (Optional) Displays help for this command. • -i interval - (Optional) Enter the interval in seconds to wait between sending each packet, the default is 1 second. • -I interface-name or interface-ip-address - (Optional) Enter the source interface name without spaces or the interface IP address: • For a physical Ethernet interface, enter ethernetnode/slot/port; for example, ethernet1/1/1. • For a VLAN interface, enter vlanvlan-id; for example, vlan10. • For a Loopback interface, enter loopbackid; for example, loopback1. • For a port-channel interface, enter port-channelchannel-id; for example, port-channel. • -l preload - (Optional) Enter the number of packets that ping sends before waiting for a reply. Only a super-user may preload more than three. • -L - (Optional) Suppress the Loopback of multicast packets for a multicast target address. • -m mark - (Optional) Tags the packets sent to ping a remote device. Use this option with policy routing. • -M pmtudisc_option - (Optional) Enter the path MTU (PMTU) discovery strategy: • do prevents fragmentation, including local. • want performs PMTU discovery and fragments large packets locally. • dont does not set the Don't Fragment (DF) flag. • -p pattern - (Optional) Enter a maximum of 16 pad bytes to fill out the packet you send to diagnose data-related problems in the network; for example, -p ff fills the sent packet with all 1's. • -Q tos - (Optional) Enter a maximum of 1500 bytes in decimal or hex datagrams to set the quality of service (QoS)-related bits. • -s packetsize - (Optional) Enter the number of data bytes to send, from 1 to 65468, default 56. • -S sndbuf - (Optional) Set the sndbuf socket. By default, the sndbuf socket buffers one packet maximum. • -t ttl - (Optional) Enter the IPv6 time-to-live (TTL) value in seconds. • -T timestamp option - (Optional) Set special IP timestamp options. Valid values for timestamp option - tsonly (only timestamps), tsandaddr (timestamps and addresses), or tsprespec host1 [host2 [host3 [host4]]] (timestamp pre-specified hops). • -v - (Optional) Verbose output. • -V - (Optional) Display the version and exit. • -w deadline - (Optional) Enter the time-out value in seconds before the ping exits regardless of how many packets are sent or received. • -W timeout - (Optional) Enter the time to wait for a response in seconds. This setting affects the timeout only if there is no response, otherwise ping waits for two round-trip times (RTTs). • hop1 ... (Optional) Enter the IPv6 addresses of the pre-specified hops for the ping packet to take. • destination - Enter the IPv6 destination address in A:B::C:D format, where you are testing connectivity. Default Not configured Command Mode EXEC Usage Information This command uses an ICMP ECHO_REQUEST datagram to receive an ICMP ECHO_RESPONSE from a network host or gateway. Each ping packet has an IPv6 and ICMP header, then a time value and a number of ''pad'' bytes used to fill out the packet. A pingv6 operation sends a packet to a specified IPv6 address and then measures the time it takes to get a response from the address or device. When you use the -I option and enter an IP address, OS10 considers it as the source address. If you use an interface name instead of the IP address, OS10 considers it as the egress interface. CLI Basics 69