Dell PowerEdge 2950 Hardware Owner's Manual (PDF) - Page 102

Installing the Sideplane Board, connector. See

Get Dell PowerEdge 2950 PDF manuals and user guides View all Dell PowerEdge 2950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Figure 3-33. Sideplane Removal and Installation 2 1 3 4 5 1 sideplane board 4 backplane connector 2 sideplane release tabs (2) 5 pins (2) 3 guides (2) Installing the Sideplane Board CAUTION: Only trained service technicians are authorized to remove the system cover and access any of the components inside the system. See your Product Information Guide for complete information about safety precautions, working inside the computer, and protecting against electrostatic discharge. 1 Turn off the system and attached peripherals, and disconnect the system from the electrical outlet. 2 Align the two guides on the sideplane board with the two pins on the SAS backplane board, and gently lower the sideplane so that the sideplane connector is fully seated into the SAS backplane board connector. See Figure 3-33. 3 Reattach any cables to the sideplane board. 4 If applicable, replace the storage controller daughter card. See "Installing a SAS Controller Daughter Card" on page 70. 5 Close the system. See "Closing the System" on page 55. 102 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
102
Installing System Components
Figure 3-33.
Sideplane Removal and Installation
Installing the Sideplane Board
CAUTION:
Only trained service technicians are authorized to remove the system cover and access any of the
components inside the system. See your
Product Information Guide
for complete information about safety
precautions, working inside the computer, and protecting against electrostatic discharge.
1
Turn off the system and attached peripherals, and disconnect the system from the electrical outlet.
2
Align the two guides on the sideplane board with the two pins on the SAS backplane board, and gently
lower the sideplane so that the sideplane connector is fully seated into the SAS backplane board
connector. See Figure 3-33.
3
Reattach any cables to the sideplane board.
4
If applicable, replace the storage controller daughter card. See "Installing a SAS Controller Daughter
Card" on page 70.
5
Close the system. See "Closing the System" on page 55.
1
sideplane board
2
sideplane release tabs (2)
3
guides (2)
4
backplane connector
5
pins (2)
1
2
5
3
4