Dell PowerEdge 2950 Hardware Owner's Manual (PDF) - Page 24

SAS Cable - ram

Get Dell PowerEdge 2950 PDF manuals and user guides View all Dell PowerEdge 2950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Table 1-6. LCD Status Messages (continued) Code E1811 E1812 E1913 E1A11 E1A12 E1A14 E1A15 E2010 E2011 E2012 E2013 E2014 E2015 Text Causes Corrective Actions HDD ## Rbld Abrt The specified hard drive has experienced a rebuild abort. See "Troubleshooting a Hard Drive" on page 124. If the problem persists, see your RAID documentation. HDD ## Removed The specified hard drive has been Information only. removed from the system. CPU & Firmware Mismatch The BMC firmware does not support the CPU. Update to the latest BMC firmware. See the BMC User's Guide for more information on setup and use of BMC. PCI Rsr Config PCI risers are not configured correctly; some invalid configurations may prevent the system from powering on. See "Expansion-Card Riser Boards" on page 98. PCI Rsr Missing One or all of the PCI risers is missing, preventing the system from powering on. Information only. SAS Cable A SAS cable A is missing or bad. Reseat the cable. If problem persists, replace cable. See "SAS Controller Daughter Card" on page 69. SAS Cable B SAS cable B is missing or bad. Reseat the cable. If problem persists, replace cable. See "SAS Controller Daughter Card" on page 69. No Memory No memory is installed in the system. Install memory. See "Installing Memory Modules" on page 90. Mem Config Err Memory detected, but is not configurable. Error detected during memory configuration. See "Troubleshooting System Memory" on page 120. Unusable Memory Memory is configured, but not usable. Memory subsystem failure. See "Troubleshooting System Memory" on page 120. Shadow BIOS Fail The system BIOS failed to copy See "Troubleshooting System its flash image into memory. Memory" on page 120. CMOS Fail CMOS failure. CMOS RAM not See "Getting Help" on page 147. functioning properly. DMA Controller DMA controller failure. See "Getting Help" on page 147. 24 About Your System

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
24
About Your System
E1811
HDD ## Rbld Abrt
The specified hard drive has
experienced a rebuild abort.
See "Troubleshooting a Hard
Drive" on page 124. If the
problem persists, see your RAID
documentation.
E1812
HDD ## Removed
The specified hard drive has been
removed from the system.
Information only.
E1913
CPU & Firmware
Mismatch
The BMC firmware does not
support the CPU.
Update to the latest BMC
firmware. See the
BMC User’s
Guide
for more information on
setup and use of BMC.
E1A11
PCI Rsr Config
PCI risers are not configured
correctly; some invalid
configurations may prevent the
system from powering on.
See "Expansion-Card Riser
Boards" on page 98.
E1A12
PCI Rsr Missing
One or all of the PCI risers is
missing, preventing the system
from powering on.
Information only.
E1A14
SAS Cable A
SAS cable A is missing or bad.
Reseat the cable. If problem
persists, replace cable. See "SAS
Controller Daughter Card" on
page 69.
E1A15
SAS Cable B
SAS cable B is missing or bad.
Reseat the cable. If problem
persists, replace cable. See "SAS
Controller Daughter Card" on
page 69.
E2010
No Memory
No memory is installed in the
system.
Install memory. See "Installing
Memory Modules" on page 90.
E2011
Mem Config Err
Memory detected, but is not
configurable. Error detected
during memory configuration.
See "Troubleshooting System
Memory" on page 120.
E2012
Unusable Memory
Memory is configured, but not
usable. Memory subsystem
failure.
See "Troubleshooting System
Memory" on page 120.
E2013
Shadow BIOS Fail
The system BIOS failed to copy
its flash image into memory.
See "Troubleshooting System
Memory" on page 120.
E2014
CMOS Fail
CMOS failure. CMOS RAM not
functioning properly.
See "Getting Help" on page 147.
E2015
DMA Controller
DMA controller failure.
See "Getting Help" on page 147.
Table 1-6.
LCD Status Messages
(continued)
Code
Text
Causes
Corrective Actions