HP Brio ba410 hp brio ba410, user guide - Page 57

Accessing Internal Components

Get HP Brio ba410 PDF manuals and user guides View all HP Brio ba410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Accessing Internal Components Accessing Internal Components Removing and Replacing the Main Cover WARNING For your safety, disconnect the power cord and all external cables. To Remove the Main Cover 1 Place the PC on a flat surface and stand behind it. 2 Disconnect all cables from the rear of the PC. 3 Loosen the two thumb screws at the rear of the PC. 4 Slide the cover back by about 2 cm (0.6 inches). 5 Tip the cover to the side and lift it off. To Replace the Main Cover 1 Position the metal flap on the bottom inside of the cover over the guide rail of the PC, leaving a gap of about 2 cm (0.6 inches) between the cover and the front of the PC. 2 Tilt the cover towards the PC. 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Accessing Internal Components
49
Accessing Internal Components
Removing and Replacing the Main Cover
WARNING
For your safety, disconnect the power cord and all external cables.
To Remove the Main Cover
1
Place the PC on a flat surface and stand behind it.
2
Disconnect all cables from the rear of the PC.
3
Loosen the two thumb screws at the rear of the PC.
4
Slide the cover back by about 2 cm (0.6 inches).
5
Tip the cover to the side and lift it off.
To Replace the Main Cover
1
Position the metal flap on the bottom inside of the cover over the guide
rail of the PC, leaving a gap of about 2 cm (0.6 inches) between the
cover and the front of the PC.
2
Tilt the cover towards the PC.