HP Brio ba410 hp brio ba410, user guide - Page 75

Replacing the Power Supply Unit

Get HP Brio ba410 PDF manuals and user guides View all HP Brio ba410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Replacing the Power Supply Unit Replacing the Power Supply Unit WARNING Hewlett-Packard does not support power supply upgrades. This information is provided to help you replace a defective power supply unit. For your safety, only replace with a power supply provided by HP support services. To avoid electrical shock, do not open the power supply. There are no user-serviceable parts inside. 1 Switch off the PC and remove the main cover. 2 Lay the PC on its side. 3 Release the power supply cables from the cable clamp situated under the floppy drive unit. 4 Press down the retaining clip at the top of the power supply unit, and holding the unit carefully, rotate it upwards. 5 Push the second retaining clip outwards and lift the power supply unit out of the PC and lay it by the underside of the PC, not beside the front panel. clip cable clamp clip 6 Disconnect all power cables from installed drives and from the system board. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Replacing the Power Supply Unit
67
Replacing the Power Supply Unit
WARNING
Hewlett-Packard does not support power supply upgrades. This information is
provided to help you replace a defective power supply unit. For your safety, only
replace with a power supply provided by HP support services.
To avoid electrical shock, do not open the power supply. There are no user-serviceable
parts inside.
1
Switch off the PC and remove the main cover.
2
Lay the PC on its side.
3
Release the power supply cables from the cable clamp situated under
the floppy drive unit.
4
Press down the retaining clip at the top of the power supply unit, and
holding the unit carefully, rotate it upwards.
5
Push the second retaining clip outwards and lift the power supply unit
out of the PC and lay it by the underside of the PC, not beside the front
panel.
6
Disconnect all power cables from installed drives and from the system
board.
cable clamp
clip
clip