HP Brio ba410 hp brio ba410, user guide - Page 81

Setting System Defaults

Get HP Brio ba410 PDF manuals and user guides View all HP Brio ba410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

HP Setup Program • Boot - for choosing your boot device order and priority. You can select the order of the devices from which the BIOS (Basic Input Output System) attempts to boot the operating system. During the POST (Power On Self-Test), if the BIOS is unsuccessful at booting from one device, it will try the next one on the Boot Device Priority list until an operating system is found. The default boot device is the floppy disk. • Exit: for leaving the Setup program. Setting System Defaults The Setup program changes system behavior by modifying the power-on initialization parameters. Setting incorrect values may cause system boot failure. If this occurs, press the F9 key while you are in the Setup program to load the Setup program's default values or select Load default values in the Exit menu of the Setup program. This should enable the computer to boot properly. Note If a Supervisor password is set, you need to enter the password to set system defaults. HP strongly recommends you make a note of any changes you make while in the Setup program. 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
HP Setup Program
73
•
Boot
- for choosing your boot device order and priority.
You can select the order of the devices from which the BIOS (Basic
Input Output System) attempts to boot the operating system. During
the POST (Power On Self-Test), if the BIOS is unsuccessful at booting
from one device, it will try the next one on the Boot Device Priority list
until an operating system is found. The default boot device is the floppy
disk.
•
Exit
: for leaving the
Setup
program.
Setting System Defaults
The
Setup
program changes system behavior by modifying the power-on
initialization parameters. Setting incorrect values may cause system boot
failure. If this occurs, press the
F9
key while you are in the
Setup
program
to load the
Setup
program's default values or select
Load default values
in
the
Exit
menu of the
Setup
program. This should enable the computer to
boot properly.
Note
If a Supervisor password is set, you need to enter the password to set system defaults.
HP strongly recommends you make a note of any changes you make while in the
Setup
program.