HP ElitePad 1000 HP ElitePad 1000 G2 Maintenance and Service Guide - Page 49

WLAN module, labeled 1. The WLAN antenna cable labeled 2 connects to the WLAN module AUX

Get HP ElitePad 1000 PDF manuals and user guides View all HP ElitePad 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

WLAN module Description Broadcom BCM43241 802.11abgn 2x2 Wi-Fi + BT 4.0 Combo Adapter Spare part number 723677-005 Before removing the WLAN module, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the display assembly (see Display assembly on page 30). 5. Remove the NFC antenna (see NFC antenna on page 38). Remove the WLAN module: 1. Release the ZIF connector (1) to which the WLAN ribbon cable is attached, and then disconnect the WLAN ribbon cable from the system board. 2. Disconnect the WLAN antenna cables (2) from the terminals on the WLAN module. NOTE: The WLAN antenna cable labeled "1" connects to the WLAN module "MAIN" terminal labeled "1". The WLAN antenna cable labeled "2" connects to the WLAN module "AUX" terminal labeled "2". 3. Release the shielding (3) to gain access to the bottom screw that secures the WLAN module to the bottom cover. 4. Remove the two Phillips PM1.3×2.0 screws (4) that secure the WLAN module to the bottom cover. Tablet component replacement procedures 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
WLAN module
Description
Spare part number
Broadcom BCM43241 802.11abgn 2x2 Wi-Fi + BT 4.0 Combo Adapter
723677-005
Before removing the WLAN module, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet.
3.
Disconnect all external devices from the tablet.
4.
Remove the display assembly (see
Display assembly
on page
30
).
5.
Remove the NFC antenna (see
NFC antenna
on page
38
).
Remove the WLAN module:
1.
Release the ZIF connector
(1)
to which the WLAN ribbon cable is attached, and then disconnect
the WLAN ribbon cable from the system board.
2.
Disconnect the WLAN antenna cables
(2)
from the terminals on the WLAN module.
NOTE:
The WLAN antenna cable labeled “1” connects to the WLAN module “MAIN” terminal
labeled “1”. The WLAN antenna cable labeled “2” connects to the WLAN module “AUX”
terminal labeled “2”.
3.
Release the shielding
(3)
to gain access to the bottom screw that secures the WLAN module to the
bottom cover.
4.
Remove the two Phillips PM1.3×2.0 screws
(4)
that secure the WLAN module to the bottom cover.
Tablet component replacement procedures
41