HP ElitePad 1000 HP ElitePad 1000 G2 Maintenance and Service Guide - Page 93

the Security Jacket., Disconnect the card reader board cable

Get HP ElitePad 1000 PDF manuals and user guides View all HP ElitePad 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

4. Remove the two Phillips PM1.3×3.4 screws (1) that secure the front cover to the Security Jacket. 5. Release the front cover (2) by sliding it partially away from the Security Jacket. 6. Lift the bottom edge of the front cover (1) and swing it up and back until it rests upside down on the Security Jacket. 7. Disconnect the fingerprint reader board cable (2) from the low insertion force (LIF) connector on the system board. 8. Disconnect the card reader board cable (3) from the LIF connector on the system board. 9. Remove the front cover. Reverse this procedure to install the front cover. Security Jacket component replacement procedures 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
4.
Remove the two Phillips PM1.3×3.4 screws
(1)
that secure the front cover to the Security Jacket.
5.
Release the front cover
(2)
by sliding it partially away from the Security Jacket.
6.
Lift the bottom edge of the front cover
(1)
and swing it up and back until it rests upside down on
the Security Jacket.
7.
Disconnect the fingerprint reader board cable
(2)
from the low insertion force (LIF) connector on
the system board.
8.
Disconnect the card reader board cable
(3)
from the LIF connector on the system board.
9.
Remove the front cover.
Reverse this procedure to install the front cover.
Security Jacket component replacement procedures
85