HP ElitePad 1000 HP ElitePad 1000 G2 Maintenance and Service Guide - Page 88

Credit card reader, Disconnect the credit card reader cable

Get HP ElitePad 1000 PDF manuals and user guides View all HP ElitePad 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

7. Remove the right-side credit card reader board (3) and cable. Reverse this procedure to install the credit card reader boards. Credit card reader Description Credit card reader Spare part number 744026-001 Before removing the credit card reader, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet or the Retail Jacket. 3. Disconnect all external devices from the Retail Jacket. 4. Remove the top cap (see Top cap on page 67). 5. If installed, remove the tablet from the Retail Jacket (see Top cap on page 67). 6. Remove the front cover (see Front cover on page 69). Remove the credit card reader: 1. Disconnect the credit card reader cable (1) from the right-side credit card reader board. 2. Release the credit card reader cable (2) from the routing channel built into the rear cover. 3. Remove the two Phillips PM1.9×3.0 screws (3) that secure the retention tabs and the credit card reader to the rear cover. 4. Remove the two retention tabs (4). 80 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
7.
Remove the right-side credit card reader board
(3)
and cable.
Reverse this procedure to install the credit card reader boards.
Credit card reader
Description
Spare part number
Credit card reader
744026-001
Before removing the credit card reader, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Retail Jacket.
3.
Disconnect all external devices from the Retail Jacket.
4.
Remove the top cap (see
Top cap
on page
67
).
5.
If installed, remove the tablet from the Retail Jacket (see
Top cap
on page
67
).
6.
Remove the front cover (see
Front cover
on page
69
).
Remove the credit card reader:
1.
Disconnect the credit card reader cable
(1)
from the right-side credit card reader board.
2.
Release the credit card reader cable
(2)
from the routing channel built into the rear cover.
3.
Remove the two Phillips PM1.9×3.0 screws
(3)
that secure the retention tabs and the credit card
reader to the rear cover.
4.
Remove the two retention tabs
(4)
.
80
Chapter 5
Removal and replacement procedures