HP ElitePad 1000 HP ElitePad 1000 G2 Maintenance and Service Guide - Page 95

Docking connector cable, Remove the system board see

Get HP ElitePad 1000 PDF manuals and user guides View all HP ElitePad 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Docking connector cable NOTE: The docking connector cable is included in the Cables/Connectors Kit, spare part number 744045-001. Before removing the docking connector cable, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet or the Security Jacket. 3. Disconnect all external devices from the Security Jacket. 4. Remove the card reader cover and top cap (see Card reader cover and Top cap on page 82). 5. If installed, remove the tablet from the Security Jacket (see Card reader cover and Top cap on page 82). 6. Remove the front cover (see Front cover on page 84). 7. Remove the system board (see System board on page 86). Remove the docking connector cable: 1. Turn the system board upside down with the top toward you. 2. Remove the two Phillips PM1.9×3.4 screws (1) that secure the docking connector cable to the system board. 3. Remove the docking connector bracket (2). Security Jacket component replacement procedures 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
Docking connector cable
NOTE:
The docking connector cable is included in the Cables/Connectors Kit, spare part number
744045-001.
Before removing the docking connector cable, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet or the
Security Jacket.
3.
Disconnect all external devices from the Security Jacket.
4.
Remove the card reader cover and top cap (see
Card reader cover and Top cap
on page
82
).
5.
If installed, remove the tablet from the Security Jacket (see
Card reader cover and Top cap
on page
82
).
6.
Remove the front cover (see
Front cover
on page
84
).
7.
Remove the system board (see
System board
on page
86
).
Remove the docking connector cable:
1.
Turn the system board upside down with the top toward you.
2.
Remove the two Phillips PM1.9×3.4 screws
(1)
that secure the docking connector cable to the
system board.
3.
Remove the docking connector bracket
(2)
.
Security Jacket component replacement procedures
87