HP Integrity Superdome SX1000 Installation (Smart Setup) Guide, Windows Server - Page 37

Install from a GUI Console

Get HP Integrity Superdome SX1000 PDF manuals and user guides View all HP Integrity Superdome SX1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

c. In the Confirm Selection screen, click Install. d. When the installation finishes, click Close to exit back to the Initial Configuration Tasks screen. Then click Close again. e. Restart the system. NOTE: Another way to install SNMP is from the command prompt, by entering: ServerManagerCmd.exe -install SNMP-Service, and then restarting the system. With this method you must still configure the service, as described in the next step. 31. After the system restarts, configure SNMP by completing the following steps: a. From the Windows Desktop, select Start > Administrative Tools > Services. b. In the Services window, right-click SNMP Service and click Properties. c. In the Properties window, click on the Security tab. d. In the Security tab, click Add to add a Community string. Name the string and assign it access rights depending on your system requirements. e. Click Apply, and then click OK twice to apply the change. f. Exit the Services window. 32. Installation of the OS is complete. After installing the operating system, perform these tasks next: • "Install the Integrity Support Pack (ISP)" (page 61) • "Activate the OS" (page 50) • "Apply OS Updates Using the Smart Update Media" (page 53) • "Enable Windows Components" (page 54) • "Verify System Device Drivers and Register for Updates" (page 55) • See if you need to perform any additional tasks described here: "Miscellaneous Installation Issues" (page 56) Then go to the sections describing configuration of the management tools, and perform these tasks: • "Configure System Management Homepage" (page 64) • "Configure the Management Agents" (page 66) • "Verify Installation of the nPartition Management Tools" (page 72) Install from a GUI Console This section describes how to install the OS using a GUI console and the EFI-Based Setup Utility (EBSU). EBSU provides an easy-to-use interface to flash the firmware, partition the hard disk, install diagnostic tools, configure storage controllers, and run other EFI utilities. To run EBSU, complete the following steps: 1. Power on the server. The server boots to EFI. You can use the EFI Boot Manager from the Enhanced interface (gray background) or the Legacy interface (black background). 2. Load the HP Smart Setup media into the server DVD drive. 3. From the EFI Boot Manager Boot Menu, select Internal Bootable DVD and press Enter. EBSU starts and displays the Welcome screen. 4. Click OK and press Enter. 5. From the Main Menu, select Express Setup and press Enter. Install from a GUI Console 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
c.
In the Confirm Selection screen, click
Install
.
d.
When the installation finishes, click
Close
to exit back to the Initial Configuration Tasks
screen. Then click
Close
again.
e.
Restart the system.
NOTE:
Another way to install SNMP is from the command prompt, by entering:
ServerManagerCmd.exe -install SNMP-Service
, and then restarting the system.
With this method you must still configure the service, as described in the next step.
31.
After the system restarts, configure SNMP by completing the following steps:
a.
From the Windows Desktop, select
Start > Administrative Tools > Services
.
b.
In the Services window, right-click
SNMP Service
and click
Properties
.
c.
In the Properties window, click on the Security tab.
d.
In the Security tab, click
Add
to add a Community string. Name the string and assign
it access rights depending on your system requirements.
e.
Click
Apply
, and then click
OK
twice to apply the change.
f.
Exit the Services window.
32.
Installation of the OS is complete.
After installing the operating system, perform these tasks next:
•
“Install the Integrity Support Pack (ISP)” (page 61)
•
“Activate the OS” (page 50)
•
“Apply OS Updates Using the Smart Update Media” (page 53)
•
“Enable Windows Components” (page 54)
•
“Verify System Device Drivers and Register for Updates” (page 55)
•
See if you need to perform any additional tasks described here:
“Miscellaneous Installation
Issues” (page 56)
Then go to the sections describing configuration of the management tools, and perform these
tasks:
•
“Configure System Management Homepage” (page 64)
•
“Configure the Management Agents” (page 66)
•
“Verify Installation of the nPartition Management Tools” (page 72)
Install from a GUI Console
This section describes how to install the OS using a GUI console and the EFI-Based Setup Utility
(EBSU). EBSU provides an easy-to-use interface to flash the firmware, partition the hard disk,
install diagnostic tools, configure storage controllers, and run other EFI utilities.
To run EBSU, complete the following steps:
1.
Power on the server. The server boots to EFI.
You can use the EFI Boot Manager from the Enhanced interface (gray background) or the
Legacy interface (black background).
2.
Load the HP Smart Setup media into the server DVD drive.
3.
From the EFI Boot Manager Boot Menu, select
Internal Bootable DVD
and press
Enter
.
EBSU starts and displays the Welcome screen.
4.
Click
OK
and press
Enter
.
5.
From the Main Menu, select
Express Setup
and press
Enter
.
Install from a GUI Console
37