HP ML150 HP ProLiant ML150 G6 Server Maintenance and Service Guide - Page 40

HDD cage, Removing and replacing a non-hot-plug HDD cage

Get HP ML150 - ProLiant - G6 PDF manuals and user guides
UPC - 884420743644
View all HP ML150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

HDD cage The server can accommodate two types of cages: a non-hot-plug HDD cage (without a backplane) and a hot-plug HDD cage (with a backplane). In the standard configuration the server will have one of these types of HDD cages installed in the upper hard drive area. Removing and replacing a non-hot-plug HDD cage The removal and replacement of the non-hot-plug HDD cage is described in the Hard Drive subsection titled "Removing/replacing a non-hot-plug hard drive." Removing and replacing a hot-plug HDD cage and backplane To remove and replace the hot-plug HDD cage: 1. Power down the server. 2. Disconnect the power cord(s). 3. Remove the access panel and front bezel as described in the section titled "System covers." 4. Remove all hard drives from the HDD cage as described in the section titled "Removing/replacing a hot-plug hard drive." 5. Disconnect the power data cables and 12C cable from the backplane of the HDD cage. Figure 3-15 Disconnecting cables from the HDD cage backplane Removal and replacement procedures 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
HDD cage
The server can accommodate two types of cages: a non-hot-plug HDD cage (without a backplane)
and a hot-plug HDD cage (with a backplane). In the standard configuration the server will have one
of these types of HDD cages installed in the upper hard drive area.
Removing and replacing a non-hot-plug HDD cage
The removal and replacement of the non-hot-plug HDD cage is described in the Hard Drive subsection
titled “Removing/replacing a non-hot-plug hard drive.”
Removing and replacing a hot-plug HDD cage and backplane
To remove and replace the hot-plug HDD cage:
1.
Power down the server.
2.
Disconnect the power cord(s).
3.
Remove the access panel and front bezel as described in the section titled “System covers.”
4.
Remove all hard drives from the HDD cage as described in the section titled
“Removing/replacing a hot-plug hard drive.”
5.
Disconnect the power data cables and 12C cable from the backplane of the HDD cage.
Figure
3
-15
Disconnecting cables from the HDD cage backplane
Removal and replacement procedures
40